Search results for query: *

I have a client with an older ip403 running version 2.1 (15). It has been running stable for many many years. The user just called saying they get a busy signal when calling into the voicemail. I checked and the services are running on the server. I opened manager and typed in the...

I have a Cisco 1841 router that seems to have crashed. The CF and AIM light are both blinking. The network ports and wic card have no lights. I can no use the console cable and hyperterminal to get to the device. It seems totally frozen or crashed or dead. Has anyone seen this happen...

I was changing the config to allow remote desktop to the server and somehow disabled the internet access for the client workstations. Below is my configuration. Thanks for the help. Result of firewall command: "sh run" : Saved : PIX Version 6.3(3) interface ethernet0 auto interface...

I just setup a brand new Partner ACS 8.0 with a voicemail PC card small. Everything on the system is crystal clear, except when I call into the voicemail. When calling into the voicemail I get a very annoying crackling/staticy sound. Has anyone encountered with before? Could it be a bad slot...

I am trying to send a customer instructions on accessing their voicemail from outside the office. I can't seem to find the instructions online. Can someone please post them or a link to them. Thanks.

I am trying to tell the system where to go when someone hits option 0. I know its not a selector code. Right now, it rings only extension 10. We would like it to ring all the extensions. Thanks!

I am having trouble getting calls for my hunt group to go to the AA. I have set it to night in manager and put in a route by call status in vm pro. I have voicemail on in the hunt group. Do I need to do something special. In the older 3.2 software it just seemed to work. It just goes to...

I am looking to setup short codes for secondary dial tone. I am on the newest release using an IP500. I have not worked with any 4.0+ system before this install. Do i put the short code only in the ARS? When I put the short code only in the ARS using 9N Dial Nsiournumber Line 0 (pri) When...

I have a pix 515 and we seem to be having a problem with it stealing some of our bandwidth. I have connected my latop straight to the t1 and have gotten full speed, but when connected to the firewall we only get 1256kb/s down. (on the laptop i got about 1450 kb/s down). I am no cisco expert...

We currently have a Cisco 871 wireless hooked up to a cable connection. We are switching over to CavTel's fast ethernet service. They provide you with an ip scheme that is similar to getting an internet T1. Are we able to program this router to accept the WAN and LAN side? We would like to...

We have a 406 V1 running 3.2 (17). We currently have a PRI with ESF, B8ZS, CPE and DMS 100 The new one was the same except running NI2. When we went to do the swap, we get the following error in the monitor. We are getting a cause=57 error See the monitor below. Thanks for the help...

I have a new install of a Partner R7 with the full voicemail system I have set everything up properly (I think). I am unable to dial into the 0 mailbox to program the Auto Attendants. I am doing this from extension 10. It says "You can not get your messages now because your mailbox is...

We have a IP406V1 with VM Pro. We are running version 3.2(17). We are running exchange 2003. The issue is that some people receive the voicemail to the e-mail and some do not. We have setup vmpro to use smtp to send the alerts. Each user has their e-mail address in manager and is set top...

We have been having issues for the vpn for some time now. We had a cisco certified tech fix the config, but vpn connectivity would still drop. We must only be missing one or two lines from either side. Maybe i have to reset the shared key on each end? Any and all help is very...

We have a Small Office Edition with the voice mail small. We have set up the auto attendant with 3 options. 1) Goes to the front desk (2 phones) in calling group one. We set it to call extension 71. 2) goes to extension 10 3) goes to extension 11 The issue lies in option 1. When a caller...

I have two seperate clients setup on cisco pix501s. One of the employees works for both companies and needs vpn access to the other site. I would rather not setup a point to point vpn between the two routers. I am having trouble initiating the connection from behind the pix firewall. It just...

I am new to the ASA series. Usually use a pix, but the client requested this. We are having a few issues. 1)We have set up access list to allow outside access to internal ip cameras using certain ports, as well as the server using rdp. Have I created the rules correctly? 2)I set up NAT for...

I am connecting to a vpn via pptp using the build in vpn connect. While connected I can NOT browse the internet. Can anyone help? Thanks

I have a client with a cisco pix 501. They use the windows vpn client to connect to another network (then remote desktop to an application server). They recently moved to a new office where i set up a pix. At first they could no connect to the vpn. To fix this I added the command "fixup...

I have a client needing to connect to his machine using remote desktop. They have one public ip assigned to the pix that also allows rdp to the server. They have extra ips. I would like to have one of these ip translate to his workstation. I have created the translation and allowed the...