Search results for query: *

Did any one try before SIP Extension over inetrnet or WAN Network. I am using AASTRA SIP phones, the extension is registered to the telephony server (TSE 3.2) but the speech is one way. What should I configure in TSE?? Is it only IP Extensions??

I know well that we have Redundancy on the network and server level in TSE but I would like to know if the below scenario could work. Do we have hotstandy for the calls in MX-one Telephony server?? Let's say that I have a call (IP Phone)and my TS (LIM1) went down, is it possible for the IP...

Hi, My system is TSW SP5 and have a problem with caller ID (CLIP)on the operator. Im using ISDN E1, and no problem with the caller ID over digital extensions but there is a problem with the caller ID on the operator. (No problem in caller ID on the operator if I am receiving an internal call)...

Hi, I have TSW system connected with Mx-one telephony server over Q-sig...where the TSW is connected to another TSW using DSS protocol (T-interface). System A :TSW which works like PSTN. System B: is the TSW which is in between the two systems, which is connected Qsig with the telephony server...

I have a qsig networking with Alkatel. my parameters as below: System release:TSW SP5 RODAP:ROU=90; ROUTE DATA ROU TYPE VARC VARI VARO FILTER 90 SL60 H'00000350 H'35440000 H'06000000 NO ROCAP:ROU=90; ROUTE CATEGORY DATA ROU SEL TRM SERV NODG DIST DISL TRAF SIG BCAP 90 7110000000000010 5...

Did any one experience in the low audio level on Analogue trunks in TSW Sp03?? I did the following: 1.cnanged TRM in ROCAI to 7 2.tried with D7 in VARC (short or long line) 3.SACOS:LIM=1,UNIT=SCP,SECTOR=REL,ADDR=58&89,DATA=6; LSATI:LIM=1,AVAL=6-x,LAW=A; x:0-15 But no improvemnet the Audio...

Hello, In one of the sites I have the following print out <IONCP; NETWORKING CONNECTION NODE/IODEV LIM USER TYPE/CON IP PORT PROC <IONPP; NETWORK PORT CONFIGURATION DATA EQU IP GATE MASK...

I hav a BC11Sp15 system, and have problem while connecting to the system through the modem ... after finishing connection to the system through the modem,the NIU2 becomes blocked and I will not be able to access the system again till I reset the LPU.. NIU2 is R10A... did any one face the same...

I have TSW connected to Alcatel..ISO and GFP are enabled. the only problem I face is when Alcatel extension calls a busy extension in TSW they can't hear the busy tone, they hear silence.!!when we call a busy extension in Alcatel we can hear the busy extension. Who is responsible about sending...

Hello, In my scenario, the MD110BC13 works as a transient switch between the BP250 and Alcatel to acheive Qsig between the three sites and this scenario works fine for the basic call features (CLIP, name) bewteen the three sites. But I have a problem with the call back and follow me features...

Hello, I have an XMP1-SL cross connector from Ericsson and I am trying to connect it through E1 to MD110 (BC13), however, its giving me an alram of "Data Link Alarm" from the MD110 side. Can anyone advice regarding this connectivity? Thank you.

My stytem is three lim system TSW SP03,When typing ALREI; it comes with LIM2 SYSTEM BLOCKED.. where actually lim2 is not blocked it could receive and make calls, and I could see the boards in CNLIP:LIM=2,DEV=YES; I have already tried BLLTE:LIM=2,ALLFM=YES; but no success. Is there any comment.

Did any one try before to connect TSW-Cisco Call manager through IP networking?? What are the recommended parameters for TSW routes

After installing MX-1 messaging 4.1 wth TSW TSW SP02, I faced a problem with DTMF detection even after installing the required patches on the Messaging server (patch 39390,39600). The case is when I connect Ericsson FCT to the TSW as analogue trunk and make an incoming call to the messaging...

In CIL can we get the post dialling digits afer the Auto attendant number (main number)?for example the main number 656564444, the you enter the post dialling digits (extension reuired) for ex.555, the CIL shows only the pilot number (656564444). can also we get the post dialling digits?

Tryig to activate the message diversion feature on digital and IP phones,the absence codes in the configuration file of the DBC425 phone, GETSC,KSTSC commands are the same. activation of the message diversion using *23*absence code# is done successfully on the digital and the IP phones. When...

Hello, We have a 2 LIMs without group switch /90 channels between the two LIMs/ Duplicated control system connected to the GSM operator through 2E1s where the Number of Extensions equals 120 extensions, where this MD110 is connected with Solidus ecare for one of the oprators. The problem we...

In MX-one we have two options for mobile extension,the first is called Operator dependant and the other is called operator independent.. can any one explain what is the main difference between the two types?

I just instlled the option unit with the DBC4224 as mentioned in Alex, and I want to activate the external bell fature. In my scenarion I have an extra bell with Input power 220VAC and I know the limittation AlEX says Maximum load on EXTERNAL DEVICE is 1 A resistive or 0.3 A capacitive or 0.3 A...

When trying to program the access code on a certain key for private line purposes using KSANI then (fro ex.) spexi:opt=n,ndc=A0A110#9,where 9 is the access code, and after dialling any number the access code will appear beside the called number on the phone display after 2 or 3 seconds from the...