Search results for query: *

I have IP Office, version 5.2(52). I have a main hunt group that calls come into at extension 8900. When I have no hours set, it rings through all the phones as it should. When I set it to be on "Night" or "Out of office" hours, it is supposed to forward to a Hunt Group called "After Hours"...

I have a 6509. When I try to SSH to it, I get "Connection Refused". I used to SSH to this box all the time. I do not believe anything has changed. I logged in via the console and generated a new key to see if this was the problem, and it is still doing the same thing. There is no firewall...

All-- I'm having some routing issues where I suspect my traffic is not following the appropriate route. I have a GRE tunnel between two sites and a VPN tunnel between two sites. I route all my pre-encrypted data traffic over the GRE tunnel and my non-encrypted traffic over the VPN tunnel. The...

In short: I connect to my PIX 501 via the VPN Client. I authenticate and the connection is there. When I ping my domain controller, I see the pings travel across the PIX, but I get "Request Timed Out" on my end. FFXOFFICE(config)# 943: ICMP echo-request from outside:192.168.50.1 to...

In short: I connect to my PIX 501 via the VPN Client. I authenticate and the connection is there. When I ping my domain controller, I see the pings travel across the PIX, but I get "Request Timed Out" on my end. FFXOFFICE(config)# 943: ICMP echo-request from outside:192.168.50.1 to...

Getting the following: FFXOFFICE(config)# 414: xauth authentication in progress for user: , session id: 609872245 415: Received response: ds3net\administrator, session id 609872245 416: Making authentication request for host 192.168.0.51, user ds3net\administrator, session id: 609872245 417...

I'm running an Etherchannel that isn't using LACP or PAgP, the group balances based on mac-address or IP address. I want to know how to: A) know which IP/MAC is assigned to which port in the group B) How to reset them and have them reassigned The reason being is that I have a bunch of servers...

How do I mirror a port on my 6509 so I can capture packets from a trouble system? I am running IOS and have 48 10/100/1000 port blades Thanks, --Andrew

I have a 6509 with a Sup 2 module. I'm trying to limit the traffic on g1/1 to stay under 200mbps... I have a policer setup to do so, but last night our traffic exceeded 200mbps for a few moments and I want to know why it did... or if I'm missing a line. mls qos ! ! spanning-tree mode pvst...

I am trying to configure a VPN for remote users to access an internal NAT 10.10.0.0/20 network and can't even get the PIX to respond to the VPN client request. Below is the config on the PIX. The PIX is passing traffic in and out of the network without issues. access-lists are working properly...

I have a 6509 with a Supervisor 2 module and a PIX firewall module. I need to rate-limit the GBIC ports on the supervisor module to keep from bursting beyond our CIR. Basically my two front-end ports are on the same VLAN and they are set in the firewall to be failover ports. I'm somewhat of a...

I'm working on a 6509, I believe it is only Layer2 I'm creating an ether channel to connect to an EMC device that I don't think supports PAgP. I've created the channel using: channel-group 1 mode on from the range of ports (2/1 - 4) that I wanted connected. The groups say it is created and...

Hey all- I'm a bit of a n00b on cisco configs. I've been through a CCNA boot camp (a while ago), and have spent time entering commands and working with the IOS envir. I am trying to configure a 6509 with a Supervisor 2 module, 2x 48 Port GigE Modules, 2x PIX Firewall Modules and 1x 6 Port GBIC...