Search results for query: *

John gave me advice earlier on some alarm codes. In my investigation I checked the voltage readings on several cards and here is what i came up with. I have (3) QPC 82E 30 Conv(erter?) cards with a voltage reading of +8.4 and -24, I also have (3) QPC 82E 30 Conv cards with a voltage of +2.4...

I'm back with a question on my SL-1XT R17. I have two codes. the First is CED070 and the second is CED 200 1. I understand that the PBX is not switching at midnight. However what is involved in fixing this issue? Does it require powering down? This old beast has not been shut off for more...

Okay John i programmed the key. However when i try to program a number it is not working. I leave the handset in the cradle push the Speed dial button and it flashes. i type in number one (first access code) and then the four digit extension to dial then i press the speed dial button again...

A user asked me to program a speed call button for him on a 2009. How do I go about doing that? How do i create a speed call code for him or find which is available? Jerry Bower Stategic Telecommunication

I have been cleaning out my frame. I came across a tn and looked it up in LD 20. Here is what it say tn 002 0 02 00 type ATT CDEN SD CUST 0 SETN 002 0 02 01 CDEN SD ANUM 01 DLEN 16 SSU 000 ICDR ICDD KEY 00 BVR 01 BIN 02 PRK 03 SSC 0000 04 ADL 75 05 06 07 MDT 08...

Back to the saga, I believe i managed to switch CPU to 0. however i am recieving the error message OVL 405. I have disk 2A, how do i restore it to the hard disk. as it stands i can not get into most of the loads i need to. Jerry Bower Stategic Telecommunication

how important is this alarm. i have gone through my capture files for the past week and it appears everyday. the time stamp shows CPU 1 each day so i assume it is not switching over to the second CPU. so what course of action would you recommend? once again it is a SL1-xt on release 17. Yes...

This is a sporadic issue. When individuals dial a number that has an automated attendant the attendant does not recognize the key inputs. Could this be an issue with a DTMF card in the switch. In the Nortel SL1-xt which cards are these and is there a way to test the channels on the cards...

How do i enable Line Mode? Please supply load directions. thanks Jerry Bower Stategic Telecommunication

What does the letter H represent or indicate following a TN? I am guessing that it is the first of two that are programmed with the same primary DN? Jerry Bower Stategic Telecommunication

My shelf went down in the switch right after that the entire switch went down for 10 minutes. I got the switch back up but i have an entire shelf down. what is the procedure to bring it back up? Loads and any other techincal help will be greatly appreciated. Jerry Bower Stategic...

I need to install a zoned paging system by Valcom. The instructions say it needs to be set up to dial a trunk access code. How do I program a specific key to dial a trunk access code in release 17? Please provide the LD and the steps how to do this. Thanks. Jerry Bower Stategic...

I have Nortel SL-1xt release 17 w/Meridian mail 12. the college is to go on break and a department with 25 phones wants them all their voice mails left in a communal mailbox to check over break. how can i set this up? Jerry Bower Stategic Telecommunication

Okay so back to my old switch. My client has asked for music on hold to be added as a feature. I am running x11-release 17 on an SL1-XT. I believe I need to install a QPC 74 card is that correct? What else is involved in adding music? Could someone walk me through the LD and the process...

How do I change the password and set second level passwords? in Release 11. Jerry Bower Stategic Telecommunication

John, Do I need the PWD2 to be able to delete the t1? I do not possess the password. How can I find it or is there a way around it? Jerry Bower Stategic Telecommunication

Hello, Can someone tell me the load to delete T1 loops in my Nortel SL-1XT release 11. They are no longer in use and just show up in PHST under load 22 each day. I want to blow them out of the system. Actually I want to blow up the system but that's a different story. Jerry Bower Stategic...

I have a DTI Trunk Loop that is enabled. However in LD 60 it says the following: service restore: yes yel alm process:yes alarm status:red ch 01-dsbl tie ch 02-24 the same. What do I need to do to get it out of alarm red? what load do I enable it in? Jerry Bower Stategic Telecommunication...

I want to know if i can program key 1 on a 2317 with a different ring tone than key 00? I am using a sl-1 xt release 11? Jerry Bower Stategic Telecommunication Field Technician

I am programming two 2317 phones. The first ones Pr DN is 1503 and it rolls over to key 01 at x8084 and if that is busy it goes to vm. This phone works just fine. So I copied this phone setup and changed key 0 to 8084 and key 1 to 1503 and if busy go to vm. however it does not work. It...