Search results for query: *

I have a remote office with BCM 50. All inbound/outbound calls route via VoIP trunks back to the main BCM 400 using dest code 9. I have installed a CO line at the remote BCM 50 and programmed dest code 8911 to pull trunk 061 to dial out on the local CO. Easy stuff. What I'm having problems with...

Does anyone know of a cordless IP phone that will work on a BCM 450. I'm looking for a phone to work on the IP side, not on a digital or analog port.

I have a customer who is moving to the BCM platform. They want to reuse several of their Polycom Conference phones (analog) The distance of the Conference phones is beyond the cable limits of a digital station. Is there a VoIP ATA for the BCM?

I'm wondering if anyone has used a Polycom Station 2-Nortel on a MICS digital port. Polycom's spec says it works on a Nortel Meridian and Meridian 1 digital port but makes no mention of MICS. Not sure if Meridian and MICS digital ports are the same.

I have an ASM using for outbound faxes. I'm trying to pull Line Pool A without dialing the pool access code (9) The port is set for access to pool A, prime line set to pool A. When going off hook I still get system dial tone and have to dial 9 to access the pool. I have also tried assigning the...

I have MICS 6.1. When a held call ends up a the prime set (under lines) I'm trying to make a group of phones ring. I've tried assigning Answer DN of the prime set to the group of phones - NOPE. I tried creating a hunt group (707) and assign 707 as the prime set - NOPE the system won't accept 707...

BCM 400 In Element Manager under alarms I'm getting Alarm ID 401 (Core Telephony - Digital station loop initialization error.) every minute. The customer is telling me that all phones are working fine. Is this a station card acting up or an individual station. I don't look into the alarms very...

I have a BCM 400 (Main office) with 3 remote offices (BCM 50's) connected via VoIP trunks. Inbound/outbound calls for all offices stem from the BCM 400 with a voice T-1. I have specific DID's routed to the remote offices. The following problems are occurring on 1 BCM only. The telco is...

I’ve been looking in the archives but I still need a definitive yes or no to a question. I have a BCM 400 (main office) with three BCM 50 (remote offices) connected with VOIP trunks over MPLS network. All BCM’s dial out via the T-1 on the BCM 400. 1. Do I have to have PRI for OLI to work? 2...

I have a BCM 400 (Main office) with 3 remote offices (BCM 50’s) connected via VOIP trunks. Inbound/outbound calls for all offices stem from the BCM 400 with a voice T-1. I have specific DID’s routed to the remote offices. On occasion all of my VOIP trunks are busy going to the remote offices...

I know that the base BCM 50 cabinet can be configured for 4 CO X 12 Digital X 2 or 4 analog port X 38 IP phone. I have an application (new site) that requires 8 CO X 26 Digital X 0 IP phone with Voicemail but have no idea what extra hardware / seats are needed. The bigger picture is I have an...

I have a NAM 4 that will not hear the callers dialed digits for AA routing (intermittant) When the problem is happening the NAM seems to hear some but not all of the digits dialed. I'm thinking DTMF receiver, but where do the receivers reside? In the NAM? base cabinet? or other? Further info...

Does anyone have a good (inexpensive) source for the 16 vac power supply (wall wart) for the Nortel IP 2XXX series phones? Thanks in advance for the replies.

I’m more of a CICS/MICS guy with some networking knowledge. I’m trying to migrate a customer from the MICS to the BCM platform. I have sites A,B,C,D with a MPLS network in place for the data side (1.5Mbps to each site) My idea is to install a BCM 400 at site A using their existing T series...

I'm looking for AOF01ENG.MAP file. I'm hoping to do backup from the bad MICS 6.1 MR software and restore to a more current 6.1 xx