Search results for query: *

Some are selling for $39.99 and some are selling for $399.99 but I can't for the life of me see what the difference is. As you already guessed, I have acquired one I want to sell (I will sell on a different site so I am not trying to break any forum rules here).

I have a 6.1 system I am installing at a very remote location so setting it up here. I only have 11 channels provisioned but I am trying to test outdialing using a full PRI. I have the outdial set up as decsending. I get a 41-0 alarm. Dial 9 and another digit gets "no free lines". Will a system...

Been Telecom Tech for a while. Now I'm the last but I am tasked with become a Data Tech to supplement the 15 data techs they got. Glad I got a job, sincerely. When I started this a month ago, they had a bootable disk and then an image on the USB depending on job. Now they want to get away from...

6.1 system with PRI. He is in commission sales. He wants his #2640 to hunt to 2639 (asst.) and then voicemail. I have read through everything I could find but when he is on the phone, it rings once on the asst.'s desk and then to his VM. His asst. can't catch the phone and neither can he. Both...

Have two hunt groups on PRI on 0x32 7.1 that is replacing BCM. Trying to emulate the BCM. They have one big pick group. 1. Group 1 has a Phantom DID assigned to it. How do I add that to the pick group? Not dialed in but can't go to sleep 'til post some questions. 2. How do you move the HG01 (or...

What are the steps for adding ASM? Can't draw DT. What am I doing wrong? It is in Mod 3. Thanks in advance

Fragmented DID range, PRI and ASM, AT&T sends 4 and they use 3. Not much time to read the manual and the BCM (never been upgraded) can't be connected to according to another onsite tech and their VM is down. Site is 200 miles away - 1. What is the best way to change the the 221 to XXX to 200 to...

Three PRI's. Clocking on 1 w/ BU on 2 and no CC on 3 Do lcnt - All 3 have 1 SLIPR Get DTA015 1 Then DTI000 Slot 1 now has 2 SLIPR, 2 & 3 still have 1 SLIPR A few minutes later, no errors but 3 has 2 SLIPR, 2 still has 1 A few minutes after that, no errors but all have 2 SLIPR's (when I dialed...

We have a 400 we are now maintaining (we have about 40 now). Also changing the IP scheme for quite a few branches. A data tech has changed several successfully but when he tries to do this one, he gets the inactive feature response. He has never been able to get in with a crossover cable on any...

Not a PC tech. Trying to reload the initial software on a laptop. It reads windows off the recovery disk but then comes up with an error that it can't find bootmgr and to reboot. Trying to decide if this PC is too far gone to get going and just replacing the hd or if the recovery disk is corrupted.

Our company is changing its IP scheme. We have about 100 BCM of various vintages in the two states I cover (some very old from company we merged with). They do not use the IP except to do admin in BCM. Can I change the IP addresses and gateway remotely or must I be onsite? Trying to avoid a lot...

We have a BCM 50 (recently installed) that will not backup to itself. Get a 12007 error on it. Is there a way to do diagnostics on the HD? As you can guess, have not been to school on one and the vendor is not getting back with me on it. Of course this was the last in a series the installed and...

Just added Executives phone to ring on 2 Assistants phones. Now they can all pick up a single call. How do I make it so after the first call picks up, the other two cannot. By the way, the Executive has a polycom with his DID too. Can't find anything like auto privacy in CLS. thanks

I have a BCM 50 to install with a broad range of numbers, 4XXX to 8XXX but only about 12 numbers. Do I still start with the lowest DID and put the second one in next even if there are several digits apart? Is it a good idea to only have 4 digits coming across the PRI? Someone else ordered the...

On a 4.0 BCM, can you do some test programming and then clear it out using something like "restart" command on a norstar and not loose the key codes? I have not installed one but would like to do test programming then wipe it out and start over once I know what I'm doing for an install.

Set up phones the same way I thought one cannot dial 9 to go out a PRI. Gets "denied in admin" as soon as she hits a 9. Her prime line is I/C like the rest and her COS is the same.

Have a BCM with a PRI pointed at it. If a call goes unanswered it goes to the prime set which is on another floor. How can I stop this so the other floors will eventually have to answer their own. Could not find any info in the documentation but maybe I was wording it wrong. thanks in advance

Three tellers have 2008 phones. One has a 3904. They all come from the same four plug outlet. One 2008 cut a cord and they replaced it. Sometime in this process the 3904 started giving strange messages on the display and the keys don't work. How can I tell what type of phone is actually plugged...

After accessing RAD, how do you make test calls from a certain phone i.e. 229 etc? I would like to select a line or intercom button and make test calls remotely. thanks

Trying to set up an acd group in a 9006 mod 80. I know MAC's in ACD but not how to build one from scratch. Would like to know the steps going from direct amo's and ccms. 1st post to this site. Thanks in advance.