Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Rhinorhino on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  • Users: techman63
  • Content: Threads
  • Order by date
  1. techman63

    TLS with J100 phones

    I have an IPO server edition 11.4.3 that we need to enable TLS and load a Third party certificate On the server and NO SBC involved for IX workplace .The customer have hundreds of J100 series phones on the internal network .What is the best approach with the minimum need to touch each...
  2. techman63

    IPOCC

    IP Office Contact Center - 9.0.3700.1422.2-OVA This my first installation of the IPOCC using OVA and I went thru the steps in the manual however after I finished with the installation according to the instruction I don’t see any application running in the TT display, I restarted the IPOCC...
  3. techman63

    IP office Networking problem

    I have 2 IP offices networking together thru MPLS with no firewall according to the IT department. One IP office is R7.12 and other is 6.1(5) it will be upgraded to R7 next week. The setup like this each IPO connected to the customer LAN thru LAN 1 and to the MPLS thru WAN (LAN2) on a VLAN .if I...
  4. techman63

    Asking for recommendation

    I have an install the next 2 weeks with a big IP office and VM pro and power users lic. and its over three thousand miles away so I want to make sure it will be ok and no issues later on, the question is do I go with 6.0(18) (its kind of stable) or the new sw 6.1 ,and who knows what bugs are in...
  5. techman63

    Callpilot with Exception 1000

    Exception 1000 Did anyone find a solution for this problem yet? I have a call pilot 3.1 and its not booting up, it’s not a software card and it’s not the power supply .I checked with RS232 connection its keep booting up and repeat the same message exception 1000 errors. I had the same problem...
  6. techman63

    Networked magix problem

    I have 3 networked magix systems (main system and one remote office are R4 and another one is R2.2) with point to point PRI,set as UDP ,the internal calls between remote sites and main sites works both way and also centralized VM works .The main system has 3 PRI cards ,2 for the PTP and one...
  7. techman63

    Sip trunks and BCM

    I'm wondering if anyone installed a BCM 400 or BCM 50 R2 with sip trunks and what were the results. The documentation only mentions the sip trunks as networks between 2 BCM or a BCM & CS1000, nothing mention about sip trunks from a Sip provider to the BCM and even if its pssible.Any feedback...
  8. techman63

    BCM 50 with Service update #2

    I tried to use that patch couple of times on multiple BCM 50 and after it goes through the process, there is an error message file transfer error .The systems has the new managements patch, any idea...Despite I can load any other patches to the system except Service Update #2
  9. techman63

    ACS patch

    I have tried couple of ACS cards with both patches 91 I and 91 J and still having problem with loosing the programming after power loss, so I just wondering if its just me or someone out there having the same problems .I tried more than 10 ACS cards originally was 91E version upgraded to I then...
  10. techman63

    CTP test Advice

    I would like an advice about the CTP test. If anyone took that test, what material they used or they recommend. My back ground is telecommunication not networking. I’m certified tech on PBX from different manufactures Nortel, avaya, Toshiba.currentely the CTP certificate is a requirement to...
  11. techman63

    Mics 7.0 networking with MCDN

    ave 2 sites with Mics 7.0,networked together thru a PRI (SL1) with MCDN enabled on both systems ,the main system has a another PRI for out going and DID calls to both systems. They both share the call pilot rel 3 (centralized VM) My problems is I can't direct the DID from the main location to...
  12. techman63

    Backup on BCM 400

    I'm working on a BCM 400 rel 3.6,everything is working fine ,however I'm trying to do a backup to my computer XP-SP2,with no luck I get differnt messages ,(error 67-the network name can't be found or the name can't be found )I 'm trying to use remote Drive.The local Drive works ok.The BCM its...

Part and Inventory Search

Back
Top