Search results for query: *

Dear Telefolks, How can the 87XX or Definity Switch be configured such that the ISDN SETUP message going out a PRI will contain the "Redirecting Number Parameter" and "Redirecting Number" information element, allowing the call to be correctly billed by the LEC, if it was forwarded by a Definity...

Dear Telefolks, How can the 87XX or Definity Switch be configured for off-net voicemail, such that the coverage call ISDN SETUP message going out a PRI will contain the "Redirecting Number Parameter" and "Redirecting Number" information element, allowing the call to get to the correct mailbox...

4630 Phone was working. Now phone still works to make calls, but touchscreen application does not start. Screen shows only text with time and date, and a= when off hook. When booting, the phone used to show a colored graphic screen with welcome to the 4630 screenphone, now it is just plain...

I'm looking for firmware for Definity Wireless Business System 9601 phones that would have been stored on a 10MB or greater translations flash card. "Status Card-Mem" will show if a card has DWBS firmware = Y. This is then viewable on a card that has it with "list config firmware". I need...

Can a Definity R9.5 accept incoming MF signalling with ANI, as in Feature Group C CAMA? I know the Switch can outpulse FGC CAMA, but I suspect it cannot accept it incoming. Incoming DTMF *ANI*DNIS* works fine, but we have an application for MF with ANI. Thanks.

Is the CMC cabinet used for Definity ONE the same as that used for a Definity Prologix Switch? Thanks!

Has anyone found schematics available anywhere for Partner ACS modules? I have a couple of defective ones which should be easy to repair, with a little documentation... Thanks.

Does anyone know who can supply the small batteries used on the TN2402 and TN798B boards to keep the proccessor CMOS alive (lithium batteries I believe). They have a number of GC5.5V 1.0F on them, but I have not found this searching the web. Thanks!

Would anyone have firmware for the old 9601+ Definity Wireless phones? This was the predecessor to the 9631. I think it used to come on a flash card. I would like to use some of these, but only one I have has new enough firmware to work properly. 8.5 or above seems to be required. Thank you.

Is it possible to use an SCC Port Cabinet J58890H as an Expansion Control Cabinet J58890N? Is conversion possible, or is the backplane completely different? Thanks very much.

Does anyone have this software hiding in an old directory? I want to provision some 46XX phones using dual connect mode on release 8.4. Avaya does not seem to have this old software any longer. Thanks, 5ESSFUN

I would like to connect a few 46XX series phones to a Prologix Release 8.4 switch using dual connect mode. Avaya web site no longer has "IP Telephone R1 v 1.1 and TFTP Server (MARCH 2001)" software available. Please advise if you know where I can get this software. Thanks!

After hard drive replacement and load of software from the Generic 4.0 and English announcement disks the TN568 reports error free install. Shortly after the audix prompt appears the unit reports return to firmware control and shuts down reporting software error code F02B. This error is not...

Definity Audix TN568 boots to Audix login prompt, then shuts down, returning to firmware control. Displays error F02B. Please help trouble shoot. Thank you.

Can a TN2401/2400 NETCON be used with a TN790B on release 8si, rather than the earlier TN794/2400 NETCON? Thanks!

Please advise where I might get newer firmware for 9601A handsets. Release 8.5 works on one set I have, but I don't have it on a flashcard or radio controller. These are old handsets used prior to the 9631. Thank you.

Dear Definity Audix Experts, I have replaced the hard drive on a TN568 Audix with Comcode 408089324 IBM DDRS-34560 drive. Generic software and english announcements load, Audix reports error free install, no errors found, then file check phase 1-5 pass. However shortly after the login prompt...

Need pinout for TN802/TN802B Cable. This cable connects the card slot to monitor, keyboard, mouse, Ethernet, modem, and com port for access to the onboard NT computer. Thank you!