Search results for query: *

Good day everyone, Does anybody know if you can page a single extension in DND mode from an attendant telephone on an eMG100 like you could on an ipLDK60? On the ipLKD60 the attendant could press the # key when they got the recording saying "That extension cannot be disturbed at this time" and...

Hello all, I have created a scenario on an eMG80 using 6 digital sets and 3 analog trunks where the customer can answer incoming calls during non busy office hours and either take the call or put the caller on hold as normal. The hold music plays advertising about the business but the caller...

Hi, I am hoping someone can point me in the right direction on setting up DISA on a UCP600. I would like a caller to be able to phone a specific DID and have the UCP600 return dial tone so that the caller can dial '9' and use the UCP600 outgoing trunks. I have enabled disa in CO Line Data >...

Hello all, Does anyone know how to upgrade the firmware on a LIP-9071 display phone using a HTTP server. I keep getting 'download failed'. Thanks, nightwolf

Hello all, I have a LIP-9030 IP phone that now shows in the display the following message: Boot: Recovery detected. Recovery Tool v3.00 Corrupted. Needs to fix. press OK: Filesystem Authorization Code: Has anyone seen this before and does anyone have any idea what the Authorization Code...

Hi all, I have a strange issue....on a new UCP 100 I cannot program the VSF-VM in station group assignment pgm 190. I have the correct range of station group numbers set up in the flexible numbering plan but it won't save. I have had no problem on the eMG80 or UCP600 although I think I've seen...

I have added the 8 channel VOIP license to a new UCP600 with 300 system licenses but I don't see the extra 8 CO VOIP trunks other than the original 6 VOIU that come with the system. Is there somewhere in the programming that the new trunks have to be activated? Thanks for any info, nightwolf

Does anyone know if the 5330e IP phones have multicast support for paging in SIP mode? Thanks, nightwolf

Has anybody connected a Mitel 5330e IP phone in SIP mode to a UCP600 using the 3rd party SIP license? I have had one connected to an Asterisk PBX but I wasn't having any success connecting to the UCP600. Thanks for any feedback. nightwolf91

Hi, I have a UCP600 & 2 eMG80 systems connected using IP Networking. I can call extension to extension between systems. What I would like to do is have the two eMG80 systems use the sip trunks at the UCP600 for outgoing calls by dialing 9 and not access the analog trunks on the eMG80 systems...

Hi everyone, I am trying to create a ring group on a LIK-50A. I have created ring group 625 with two members, stns 103 & 105. Station 103 has a DID. I have also created forced forward in the group attributes (Pgm 191) to forward to a system speed number. I have programmed a flex button on stn...

Good day all, From what I've been told you do not need a license to call extension to extension between LIKs. I have tried setting this up in the networking data program. I have voip trunks at each LIK. At pgm 324 I have CPN information ip address as the voim at the other LIK and the MFIM(E)as...

I have a Tortech PA-35 paging amplifier that I would like to connect to a telephone system paging output. This amplifier does not have the typical 600 ohm telephone paging connections that most amplifiers have. Does anyone know if it is okay to use the MIC 1 input or is it better to use the AUX...

Is it possible to program speed button to a flex key on a 8040e set? This is for a hotel and I have programmed a room check-in key but I need to access the speed key. Unless I'm doing it wrong and there is a simpler method. This is the front desk phone on a LIK100. Any help is appreciated. Thanks.

How do you change the software version on a LIK 100 from office to hotel? Uploading the hotel version software doesn't seem to change anything either in software upgrade or database upload. Any help with this is appreciated.

I am not a Panasonic tech but I have acquired a customer with a KX-TD1232 system....-4 I think. Anyhow all the telephones, mostly 7431 sets have a DND/FWD button where they can press the button and put the set into do not disturb mode where the light is on steady, or fwd na/busy to 165 (VM)and...

I am trying to connect a 12 button DSS module to a 10 button 8040L i.p. telephone on a LIK50A. I must be missing something because I have serial DSS allowed in Pgm 111 for stn 103. I am using web admin and in Pgm 110 when I choose DSSDLS1 (map1) for station 103 and enter the associated station...

I am having audio problems when using the Phontage softphone remotely. I can call an external number and it will ring but when it is answered there is no audio in either direction. I have opened the following ports: 5588 6254 8100-8171 8700-8701 1720 2048-3071 7000-7015 7100-7115 7300-7315...

First install after course and I can't believe I have forgotten which attribute to change to activate the voice mail. I have VSF access enabled in station attributes but can't access voicemail. Any suggestions would be appreciated. This time I'll write it down. Thanks

I know that a NAM 4.1 will work with 7.1 software but I have a customer with a NAM II 2.1 that is upgrading their MICS 1.1 to 7.1 in order to use a PRI. Does anyone know if the NAM II 2.1 is compatible with 7.1 or do they need to upgrade their voice mail to a call pilot? Thanks.