Search results for query: *

I added new logins a few years back on our S8500. But now the add and cha login command is invalid. Hmmmm but it works fine on CM 2.0. I don't find the Security/Administrator link that was advised in the thread690-1403742 available with a craft login. Did CM 3.0 change the SAT login feature?

Can someone refer me to where I can purchase a refurbed E1 card for the IPO in the US? thanks in advance

Hello, I have an M1 on 23.18. I bought it used on ebay and don't have all the manuals. I am in the process of placing and order to ugrade to 25.4 I don't have access to nortel.com to search for manuals. Can anyone send me a configuration guide to install T1 PRI? I also need to find the pin...

TN767 question: How do i set a TN767 to be the slave to the network? My provider is getting clocking errors. International dialing question: I need to dis-able the Int'l flag being sent to the T1 carrier (or strip the 011) How can i dis-able the flag? I tried stripping the 011 in the route...

I have a very old M1 Opt 11c. I think it's rls 13.x How can I enable all the other dn's (key's 01-04) on a 2616 to forward or hunt to 5100 like key 00 does? DES 5115 TN 002 0 00 15 TYPE 2616 CDEN 8D CUST 0 AOM 0 FDN 5100 TGAR 0 LDN NO NCOS 0 RNPG 0 SCI 0 SSU XLST SCPW CLS UNR FBA WTA...

Has anyone seen the error message " Must have normal button for display module" when deleting a station? This is on a G3si v2.0 and the stations is an 8434D. History log shows, HISTORY Date of Loaded Translation: 5:54pm Fri Nov 12, 2004 Date Time Port Login Actn Object...

Hello everyone, I have a support question, The scenario would be that company "A" has 3 G3's networked together (QSIG) 1. Is it possible to have a hunt group to a voice mail/gateway that contains members of all 3 switches switches? For example; the hunt group has a QSIG link from each of the...

Good morning Everyone, I find after a remote "system reset 1" I am unable to connect to the switch (G3csiV12) with ASA. I can ping the ethernet port. It's there and awake. I tried busying and releasing the ethernet port and board but still cannot establish a connection over the Lan. If...

Hello All- I have a M1 @ rls 16 (don't laugh please) Does anyone know how to turn CLID on to the universal CO board?

I changed system parameters features to have "tone" on hold and also heard dusring transfers. The cor's have Hear System Music on Hold? y I don't hear a tone when I am transferred or on hold. Did I miss an area? display system-parameters features Page 1 of 13...

I just got a Call Manager 4.0 I have built the server but have not started any configuration. Why? Because I have no Cisco knowledge, yet. Does anyone have a cheat sheet (used in a lab?) for a quick and dirty installation to get a few IP phones working, dial over the T1 trunks in the router...

I have analog w/caller ID ang get CPN/ANI, i.e. Company Name (in first 26 characters of the 8434 display) and the ANI after (408XXXXXXX) I don't remember seeing the CPN/name of the caller on T1. I only saw the ANI.. Should I always expect to get CPN/ANI from analog? And should I expect to...

I am trying to bring up a an 8434DX phone on a TN2224B board. I bought it refurbished. (I've haven't seen or used these phones before now) I have the MSP1 power supply that shows -48vdc is good on pins 7 and 8 of the 8 cond jack. I have the sets wired to pins 4 and 5 of the 8 cond jack. I...

I have CM 2.0 on a CSI which is behind another switch. I wanted to simply add a few analog ports to a trunk group on the CSI for dial out access. Are there a few quick and easy steps to place calls using ther FAC? Dial in works fine. But when I try to access (trk/grp1) I see COR issues. I...