Search results for query: *

I have an Avaya definity with 0 SIP trunks. CM version is 5. What is the pricing for SIP trunks and how are these licenses normally installed

We are looking at a callxpress voicemail system. Below is the integration guide. From looking at our licenses I know we already dont have SIP trunks as it is listed as 0. Also I believe we are on an Avaya software load of 5 as I see this in the web interface, install one of the follow...

Hello, We have a definity system. We have remote offices that use the Avaya 46xx series IP phones. Is there an avaya part that will allow an ip phone to analog converter? I would like to hookup a fax machine, etc. Thanks

We have an avaya definity system. How do I tell if we have Avaya Communications Manager SIP Station protocol ? I reached out to Avaya and got the run around.

Hello, Within Avaya Site Manager, ARS Analysis table (list ars analysis location 1) we have some entries I believe are no longer needed. For instance we have entries for digits 3,4,5 for min and max digits of 7 going out route path 4 hnpa. If Im not mistaken I believe these were needed...

Hello, Since we lost power from hurricane sandy we are unable to access the s8700 via the network. if I connect a switch and assign ips on both ends, we are still unable to connect. Could the network card be in a down status on the s8700? Next I try to administer the s8700 through SAT...

Is there a way to Backup Voicemail Forward Extensions Externally yes but can you limit ?? External Users hook phone into system via VOIP Caller ID 16 port single line appears to offer, but what about PRI(ISDN)? Scan Calls and intercept from Voicemail ?? DVSS (Call Screening ) can you...

Below is my system information and version number. We want caller id on our pots and t1 lines. I know the pots lines come in on one of the 408's and the t1 over the 100d. What would be needed to enable caller id? What reprograming would have to be done Thanks Magix Release 4.0 v7.0 A...

We had a former employee that left. I wiped his entire AD account. Now about a year later we need to review some emails. I have recreated the user in AD. To restore invidual emails with 9.1 I can just select the emails under Microsoft Exchange Mailboxes and not worry about Exchange options...

Hello, Just today I noticied an interesting issue in my cisco 2960g logs. It appears one port is "flapping" %SW_MATM-4-MACFLAP_NOTIF: Host X.X.X in vlan 1 is flapping between port Gi0/36 and port Gi0/37 once I disable the dell server on port 36 the flapping stops. Cisco is saying bad nic...

I noticed that the preparing network connections was hanging for a few minutes after boot up. So I looked around the event viewer and noticed that DNS server service is starting about 3 minutes later than other services. I also noticed that since DNS server is not starting quickly other...

I have some questions on arp,mac and ip if PC 3 is going to be communicating with Server and initates an ARP request how is it handled in the below diagram and why? Router A ------ Serial Connection ------- Router B | | Switch A...

if I have two routers with serial ports can the following exist and be able to talk to each other. or must two routers always connect to each other within the same subnet? router a s/1 192.168.7.1 255.255.255.252 router b s/1 192.168.8.1 255.255.255.252

Just recently I and my users have been experiening dropped calls on one of our lines. If Im reading the SPM report right, its trunk 802 which is a pots line. Should I get the line tested by verizon or could a port on the board be failing? Lastly I have the below system and have a 408 GS/LX...

Is the decision between these two is how many add on cards Im going to need and how flexible I want to be for future growth?

Right now I have a managed router and am trying to decided if its worth it to learn the router and save the company $$$. I currently have cisco switches and pix's. Should I take over the router? Is the setup pretty straight forward?

I'm trying to get a Windows 2008 DC into my Windows 2003 Active Directory environment. Right now I only have one Windows 2003 Domain Controller. This is all taking place in a LAB enviornment. I start by doing all the ADPREPs switches outlined in the TECHNET article. I use the ADPREP via the...

I have built a windows 2003 server on different hardware from what AD is running on now. After I install backup exec 9.1 ( for now ) to a different location I proceed to do a full restore in AD non-authoritative mode. once that is done I replace the boot.ini,hal.dll and ntoskrnl.exe to the...

i work in a small business ~ 100 nodes. I have some cisco switches but would like to experiement with another ip range, currently using 192.168.1.x. I would like to use 192.168.3.x or 10.0.1.x . Which router on ebay would allow me to tunnel my traffic from the 10.0.1.x/192.168.3.x to network...

what is a good program (possibly freeware)to use to monitor network traffic?? im mirroring a port on my cisco switch now for surfcontrol but would like a more informative program Thanks