Search results for query: *

I know the G350 and G250 do, but does the G700? Thanks!

IPO 406 2.1(15) DCP-30 4.1(15) ISDN-PRI No analog lines DID Service This particular system has been working fine for some time now. They’ve had a few upgrades, but aren’t on the latest version. They are having a problem forwarding calls to an outside number. I’ve searched previous posts and...

S8700 R11.3 TN799DP FW 10 TN2302AP FW 72 TN464GP FW 08 I have an R11.3 S8700 with redundant SI cabinets with 8 single-cabinet G700 remote locations. Each location has it's own Robbed-bit T1 with DID service and one or two analog cards. The entire network is all IP phones, with a few analog...

G700/S8300/IA770 - 3.1 with all patches as of 3/31/06. IA770 is not running. When I do a "process status" is says "Messaging 0/1 DOWN" It's H.323. Signal Group says "Far-end bypass" and trunk group is "OOS/FE-idle" Messaging is enabled. My license file has the IA770 stuff on it and is...

In the Status Summary section of my S8710 servers (CM3.0) it says... Duplication: hw Standby Busied? no Standby Refreshed? no Standby Shadowing: off Duplication Link: down USA1...

I have an IPO 406 (3.0.44) with VMPro. Calls come in on 12 loop-start CO lines and go directly to a hunt group that has one member, no voicemail and no queuing. This one member (extension 200) has 13 call-appr buttons. Call Waiting is ON in the hunt group AND the station. The "no answer"...

I have an S8700 (CM1.3) with a mix of 4610s and 4620s (Not sure of the firmware version-I’m not on-site-but it should be a version that was available around the same time as CM1.3). I have 9 different locations including the main location, with each location having a G700 with an S8300 LSP...

What is the button type that lights up when there are calls in queue? I've seen in mentioned here and in the documentation, so I know it exists. But, I can't seem to figure out which feature it is. Which one is it? Thanks!!!

I have two phones. One is a 5420 and one is a 5410. The 5410 has bridged appearances of the 5420 (all of them). The incoming call rings through a hunt-group where the only member is the 5420. If you answer the call on the 5420, then bridged on to the call on the 5410 (so now both phones are...

I can't get the MOH to work via an announcement on a G700. Here's what I have done... I have a 2 G700s with an S8300(R3). All virmware updates and pathces have been applied to EVERYTHING! I added the gateway-annc board on mg 2. I uploaded a .wav file (a mono 8khz sample rate .wav file) to...

Does anyone know how to delete files from the FTP directory of an S8300? Since it's only an anonymous FTP server, I don't seem to have access to the remove command. I can't do it from via telnet either (bash prompt). That may be because I don't know the command, I dunno. I tried "remove"...

IP 406 V1 R3.0(40) Has anyone ever gone through and documented what happens with queue calls under most circumstances? I am having several inconsistent issues and cannot really find a list of what happens to calls when they meet certain criteria. For instance; What happens if you a call...

I'm getting so annoyed with the continual pop-ups that are caused by the G*! D*&MED web interface to the S8XX platforms. Does anyone know of any security feature I can activate (or deactive) in Windows that will make this stop? I've added the service port (192.11.13.5) to the trusted sites in...

Whenever I get a new IPSI board, there is a 25' grey cable with a female 9-pin connector with the slide-lock on one end and pair wires on the other. I assumed it was used to connect to the 9-pin connector on the adapter that goes on the amphenol cable on the back of the cabinet, but that is a...

Hi everyone. Does anyone know if there are LAN cards that will fit into the 7700 chassis? If so, what model # am I looking for? I don't use the phone system, but if I could use it for my LAN switch, that would be cool. Thanks!

I installed a 406 with a PRI and went to program the outbound callerID. So, I set up the short codes to send out the DID number. Example: SC: [9]1N; TN: 1Ns925555E It didn't work. The caller received to callerID at all. Talked to tech support and they said it should have been... SC: [9]1N...

I know IPO has had the "universal" incoming call routing where you put in a "*" in the incoming number field and a "." in the destination field. The problem is sending the calls to VM. This setting seems to override individual settings, so you can't add an individual entry for a specific DID...

I have an S8300 Multivantage 1.3 with an IA770 1.1. I just completed a firmware upgrade on everything in the system (S8300 patch, IA770 patches, MM boards, MGP, P330). I check version compatibility left right and center and made sure I wasn't upgrading with firmware that wasn't compatible...

Has anyone ever done a point-to-point from the US to a country where they use E1s? How does that work? As near as I can tell, T1s and E1s are not compatible. I'm sure this is done all the time, but I'm stuck at where to start. Any thoughts? Thanks!!!