Search results for query: *

Need help , plantronics cs50 headset not ringing on our nec 2400 ipx , we use series e and i phones , thanks.

I would like to know how to hook up an adtran csu to the power supply of the 2000ips , I know it goes to the -27 volt but do you keep the jumper in the rg and ground connection or do you remove , if so where do you connect to rg or ground , thanks.

Where can I buy good loop current regulators , would like to purchase from a known dealer that takes PO's as payment , I work for an educational system , thanks for any idea's.

We have one 2000ips switch that the MWI does not work on any stations , any help would be appreciated.

I would like to know the proper grounding of the field wiring coming into a 2000IPS. We have four buildings , one has a 2000IPS feed from building two ( voice and T-1 ) Hub site. Building three and four are feed from building two ( voice only , no 2000ips switch ). At all four sites the field...

Is their a command on the 2000 ips with the cp-24 cpu that you can set a default ring tone for all phones. We have upgraded 53 switches and our customers are not happy with the ring tones changing after upgrade. Any help would be appreciated

I have one 2000ivs2 that when you dial out their is a delay of at least 4 to 5 seconds before it begins to dial out. Checked with my other switches an all seem to match in the programming. Any help would be appreciated.

Is their a command to have cfa lite on when call foward all on DID,thanks.

What is the procedure for installing a new 16ELCJ card , we are using 16ELCJ-B cards in all 4 Pimms. When I plug in the 16ELCJ card no lights come on. Any help is appreciated.

Could someone tell me or where I can find the cmd. for outgoing cid on our 2400imx, I need the cmd for station only if possible. Thanks

I have a 2000ivs that I can not remotely connect too,all I get is a busy. Direct connect is fine,could the cp14 telco side gone bad?

What feature or command is used to perform this,thanks. Also, there is a built in feature of the 2000 to alert up to 2 stations when a user dials 911. It basically rings the phones and lights an "Emergency" key on their phones. The key will remain lit and you simply push the key to get more...

We have a cp-24 where we took 2 analog cards and switched them with 2 digital and changed the lens number and re-cross connected them to the right lens.In cmd 10 we just changed the extensions to go to the right lens,then we begain getting trouble tickets that the call forwarding was wrong on...

Is their a command you need to change if you remove the batteries of a 2000ivs and use an UPS instead.Thanks

After upgrading and installing data base from our cp-14 to a cp-24 pim 0 and 1 are ok but pim 2 relays on power supply chatters and cp-15 on pim 2 does not activate. Any help would be great.

We have 50+ 2000ivs2's all with matworx 3.5 on all at site computers. I think I heard that matworx 3.5 may be free software now. What I need to know is if their is a place on line or someone who knows how to use an old copy to reinstall on a computer that the HD took a dive. Like I said , we...

We have a 2000ivs2 where a 8 button dterm phone that the answer and message waiting light is blinking.Had to reset switch to fix, is their a better way, thanks.

What cmd do you use to check your sense wheel settings ?Thanks

I know I have asked about this before but here I am again.My DSS does not transfer any Ext's,off hook or on speaker, BLF works fine.I am only using the DSS on campus only,I checked all programming and it all looks good.I even CCC all data on DSS and rebuilt it but to no avail.I have been...

We have a remote pim ccis over a pri that the caller id does not correspond with the assigned did.Each ext. has a different did assigned.When they call out only the sites main number shows up. Any or all help appreciated.Its a 2000ips cp-24 (we are not using the ip format at this time )