Search results for query: *

Has anyone successfully set up a video conf call using a BRI ST module on a BCM 400? I am unable to complete a call or receive an inbound call via the BRI module. I have 6 DIDs that are associated with 6 Companion DNs. Two DNs per Loop with a total of 3 Loops. I also have a Target Line...

Has anyone had problems with Visual Messenger msgs showing up hours or days after the vmx was recorded? I have seen instances where the messege shows up late and am unable to find a reason why. Anyone? id07355

Is anyone familiar with the configuratino settings for a Lantronix UDS-10 that is used for telnet access to an Octel250/350? I am looking for teh correct port settings to allow telnet access. Anyone? id07355

If anyone can help me out, i'd really appreciate it. I have mermail on my option11 and when a user is in leaving a vmx, they have the option to press 0 and exit out to an attendent. That paramter is not set up in Mermail and I dont know where to set it up. Anyone have any ideas? Thanks in...

Can anyone verify the M3904 phones will work on an Option11 running Release 25 version 2111 Issue 10? Please advise, I am looking to get rid of my 2008s and 2616 and replace them all with 3904s. Thank you. id07355

Hey Everyone. I have a question on how to adjust/change the ringer type on an M2616 phone. Looking through the handbook doesn't state anything helpfull. Does anyone know how to change the ringers on these phones? Thanks Clyder

Does anyone know what this error msg means? Reverse RPC connection with Admin Server cannot be established. Whenever i try to create/view/delete a mailbox i receive this error. Does anyone have any experiance in dealing with CallPilot at all?

Hi, i have an Octel 250 and am using dial up access to it. However, due to a new product we recently aquired, i would like to setup Telnet access to the Octel. Does anyone have information on how to set this up or know anyone who does. Out with the dial up and in with the telnet. Thanks in...

Hi everyone. I recently came upon a request to route all long distance phone calls originating in our Option11 out a specifig Route to be handled by a different switch. But all locals calls should remain local and go out the local loop. I understand how to point an NPA to a specifing RLI, but...

Gentlmen, I have an Option11 at site A and an Intecom E14 at site B. What i am doing is sending every long distance telephone call that is dialed from the Option11 over a PRI to the Intecom. I want to require the employees on the Option11 to enter an Auth Code after each long distance call...

Here is a good one for everyone. I think i am having issues with glare on PRI circuit that is connected to my Option11. I can monitor the circuit and watch all circuits go busy instantly. Seems like the call is tieing up all the available circuits and then denys any new calls through. Has...

Can anyone help walk me through updating the NPA,NNX tables in an Option11c for local calling areas. I have some new exchange numbers that need to be added in order to make local calls. I have very limited knowlegde of this on a Nortel Product, I'm an EADS switch tech. Any help would be...

Hi everyone. Does anyone know what commands are used to check if international dialing is enabled? And if not, how to enable it? Any help would be much appreciated. THanks id07355

Ok , here is what i got: Our Option 11 is rejecting calls from my switch switch over a TIE line. Sending switch is an intecom, (shouldn't matter) I'm sending 10 digits out over the TIE line and i don't know how to check the option11 to see why the call is getting a fast busy. Does anyone know...

Here is a list of Softkeys used by Procomm for access in a Meridian Mail System In case your softkeys are not preprogrammed I used the following configurations under the keyboard editor. Remember - vt220 configuration - F1= ^[[17~ F2= ^[[18~ F3= ^[[19~ F4= ^[[20~ F5= ^[[21~ This will...

Does anyone here have knowledge on which command is used to lookup the Model Number on an Option11? I know you can use LD 22 to look up the Issue and Release. Thank you

Hey guys, rookie here so bare with me. I was asked to add an area code to our Option11c to allow toll calls to that area. Can anyone help me with which load to use. I am asuming it is LD 90 but i am unable to determine where to go from there. You know how confusing that Software I/O guide...

Hi, i am having a little problem with a meridian mail system that is tied to an Option 11c. Can anyone tell me what LD command or other command is used to access the meridan mail system?