Search results for query: *

Im replacing a d500 with a new shoretel. the original vendor holds login info and not cooperating.all i want is details on call flow to config my new system. can i pull config or database files? any ideas?

I have a bcm 400 4.0 with a dsm 32 on bus 7.On bus 3 there is a 4/16 which we are not using analog side of module. My problem is that I only get 16 ports on dsm32.Will bus 7 not support dsm32? My plan is to swap modules on buses 3 and 7 and replace 4/16 with dsm16 since on analogs are needed...

I have a opt11 with 50 users that need to add a call pilot mini to. MAC work has been the extent of my experience on the Meridians. Never installed a call pilot from scratch. Ive been stuck in BCM land so its been a while since I worked in the LD's. Im confident I can do it, I just need some...

Can I activate or enable dial in modem via telset admin. Customer in another state and bcm50 not on network. I need to walk customer thru telset so I can access via modem.

I ran the 4.0 check tool . CDR storage exceeds 200mb. ???????? How do i clear this. Wont run upgrade untill fixed.

Mics 7.0 with 6 base stations. I can connect and establish a call, but will not hand off to other base station. not sure what im missing.

i got some wierd stuff happening. can any one help... TIM208 09:35 13/10/2005 CPU 1 INI000 0000002F 09 36 29 00000000 00000000 00000000 00000000 1 0 00000082 DSET000 DOWN LOAD 0 0 0 0 0 0 0 58679 INI010 00000058 00000059 0000005A 0000005B ACDR ACTIVATED ERR5417 0000B0E5 00000807 ESDA002 4...

% % PWR001 PWSP 04 1 2 % % PWR000 PWSP 04 1 2 % % PWR001 PWSP 04 1 2 % % PWR000 PWSP 04 1 2 IS THERE OR IS THERE NOT A PROBLEM. IF SO WHERE IS 04 1 2 LOCATED?

SINCE BEFORE OUR UPGRADE TO SUC 3.0 MY 81C HAD MANY DEAD ANALOG TNS. RECLAIMED QUITE A FEW BACK AFTER THE UPGRADE. NOT SURE WHY.NOW IM DROPPING PORTS AT AN ALARMING RATE DUE TO STATIC OR PLAIN DEAD (NO BATT). ANYONE ELSE EVER HAVE THIS?

WE SWITCHED TO PRI SOME TIME AGO, AND SINCE I FINALLY GET A CHANCE TO FOCUS ON JUST OUR PBX I WOULD LIKE TO PULL OUT ALL THE UNIVERSAL TRK CARDS WE NO LONGER USE. IVE ALREADY DELETED DID'S AND COT'S IN LD14.NOW IVE NOTICED AN ERROR AND WOULD LIKE TO STOP IT. ERR020 44 0 15 ERR5512 44 ERR020...

We have a call accounting system which is used to bill different cost centers and reasearch questionable usage on the pbx.this systems limitation is set by the amount data my pbx will send(via smdr port). Were can I find info on manuplating this ports settings?

I have a ring down which has no dialtone.I thought it was a bad port. 3 ports later I outed and rebuilt. I get dialtone on port until ftr hot d 4 2222 is added. Am I missing something?

I want to allow for 0+ dialing for collect calls.my lec says its my equipment restricting that from happening.if i dial my acod to directly access the trunk , o gives a fast busy.how can i see how 0 calls are routed?

Could someone listen to my conversation at my desk thru mic on my 2616 in idle state? How would that be configured?

Doctors offices subscribe to answering svc. for after hours calls. How does this work? How does the service know how to greet each caller? What type of trunking do they have?Does info pop up on pc screen? What type of equipment does this? Is there still room for more business like this or is the...

SINCE UPGRADE TO SUC3.0 WE STARTED GETTING REPORTS OF EXT'S NOT GOING TO VM AFTER ROLLING TO 2ND LINE.NO ANS ON MAIN WORKS BUT LINE 2 WONT. ALSO WHEN ROLLING TO LINE 2 , SET STILL RINGS INSTEAD OF BUZZ. WHENEVER PROG. NEW SETS MARP IS ASSIGNED, BUT SYSTEM WIDE MARP IS NOT ACTIVATED. COULD THIS...

WHEN CALLING OUT TO # WITH PRIVACY MANAGER(BLOCKS UNIDENTIFIED #'S)CLID INFO IS NOT SENT. WHEN ACCESS CODE ENTERED AND SAME # DIALED THE CLID INFO IS SENT AND CALL COMPLETED. WHY IS "9" STOPPING THE CLID INFO?

HAVE A PC W/PROCOMM FOR MAINT TERM ON 81C AND MERMAIL.CAN I INCREASE BAUD FOR MERMAIL?

I HAVE MULTIPLE TRKS FOR DIAL 9 GRP.HUNTS FROM TOP DOWN FOR INCOMMING. INCOMMING CALL ON THESE TRKS SHOW X1X-X1X1-T# ON DISPLAY SETS.IF YOU DIAL X1X-X1X1 FROM ANY SET, NCOS AND ALL OTHER RESTRICTIONS ARE BYPASSED AND A TRK IS GIVEN TO DIAL ANYWHERE.NO 9 IS NEEDED TO DIAL X1X-X1X1.SOMEHOW THIS...

I HAD A POWERSUPPLY GO OUT ON CPU 1 FOR 81C. SINCE REPLACED CPU 1 HAS ERRORS % % SCSI115 Error Reading from CDROM, sector 16, errNo 370001, sense 2, addSense 3 a % % CIOD053 CMDU 1 CD-ROM corrupted WILL A SYNC W/SIDE 0 HELP?