Search results for query: *

I recently ordered three of the DTL-8R-1 cordless phones (SL1100) and found that they have been replaced by the DTZ-8R-1. I liked the DTL phones but not so much on the DTZ. Im wondering if anyone has any info to share on the DTZ? Heres my take: The good: 1) Contact list for 100 entries...

Hello, Ive decided to finally try and back up a large 824 system that I service. I didnt know until recently that it was possible. Im getting close but need some help. I have an 824 DR3 here in the shop. Ive got the RAD not fast rad) connected and can connect to it using NRU11. I can make...

Does anyone know if the Partner Analog Station Ports provide disconnect supervision? I have a customer that wants to purchase an ACS R7 and connect a Voice Response Unit via 2 analog ports. The VR unit vendor says that the ports MUST provide disconnect supervision.

Im using an AD8 on the NEC ProII. I have never been able to figure out how to set the AD8 to transfer offsite. I know that I could use offsite forwarding from a station but that isnt available on this rev cpu. It seems that the AD8 is designed to do this (in the transfer field) but it wont...

Can 2 of these systems be linked via T-1? Im looking to have station dialing and transfer trunk calls from one system to the other. I dont need the details just need to know if the concept is viable. Thanks!

I just installed an AD8 in a 2000IPS. This replaced a worn out Repartee that was connected with MCI link. The AD8 doesnt need the MCI link (Ive been told) and in fact all integration seems OK except TRF to VM. When pressing TRF and VM pilot# you hear 'enter sec code' instead of main greeting. I...

If a multiline user also needs a cordless extension (car sales)what are my options with VM? I have several ideas but none of them seem to fit all my criteria. What I would like is to have calls ring the multiline and if not answered go to the cordless. If the cordless isnt answered the caller...

I have a Ds1000 installed at my home/business. The system is great except that RFI from the system is wiping out my ham radio receiver. Ive done some investigating and found that the interference does not come from the ksu but from the digital keysets. Doesnt seem to be related to wiring only...

Hi, Ive read some other posts concerning grounding and I know this is a subject with alot of opinions. Most of the systems I install include a panamax surge protector along with a co module. The Panamax literature shows a connection from the phone system to the pananmax module. I called them and...

Is it possible (ACS 7.0) to have incoming CO lines ring once and then only flash? This would be when phone is idle. Delay ring doesnt solve this. Thanks.

Is there any way to have 2 users share 1 phone but each have there own mailbox with separate MW indicators? I dont want to use notification to an outside number.

I have a situation where an AD8 on a proII needs to answer a call from outside and after a one key dial from caller, hookflash the co line and send the call to another number using centrex transfer.. I know how to accomplish this using off-site transfer on the proII (I dont have the correct...

how does the ds1000 compare to nec's elite line? mostly Im concerned about reliability.. does anyone have any comment regarding the ds1000/2000? thanks

I need a source for the 3.6volt 60maH nicad with connector used on the elite 48 for memeory backup. I have found lots of 3.6/60 batteries but not with the plug. I dont want to reuse the old plug. Also, has anyone experienced problems with replacement cpu batteries on the pro II? thanks!

ANY SUGGESTIONS WHERE TO FIND THIS SOFTWARE?

WE ARE USING AN ELITE 48 CNF8 CARD AS A CONFERENCE CIRCUIT FOR A NEC 2000 PBX. OUTSIDE CALLS RING INTO TRUNK PORTS ON THE ELITE 48. INSIDE CALLERS (2000) CALL AN ANALOG EXTENSION HUNT GROUP WHICH ALSO RINGS IN ON ELITE TRUNK PORTS.THE 2 SYSTEMS ARE SIDE BY SIDE. ITS NOT WORKING WELL. LOW VOLUME...

I have s700 which is good for 500-700 series CPU. I have Electra which says its good for 450 and lower. I thought it was called s400 but its not. I need software for a 4.89 or close to it CPU. Is it s400? Where can I get it?