Search results for query: *

We have some nodes with VPN connection and central operator at one node. One of satellite node has Cisco Call Manager connected via ISDN QSIG. The satellite node acts like transit node. When calling from node (A) to Cisco via node (B) as transit SEND SETUP from transit node (B) to Cisco contain...

Someone have userguide for Dispatcher application Ddu?

Hi all Anybody know where to find a Signal Trace Interpreter that handles TL11 and TL30? Trident

Someone know which ports that needs to bee open on a firewall when EBG is connected to ELU32 (IP networking)? /*Trident*/

What is the different between rev. 8C and rev. 10C? And how to "upgrade" LPU5 to rev. 10C? /*Trident*/

Can anybody help: I have 2 LIM no GS: LIM1 set interface line x1 ,tmode=framed ,cmode=slave ,idle=0x54 Status Running Name LIM1 IP 10.1.10.2 CES Type SDT Mode ECES Payload ms/bytes...

/ BC12 sp3 / Case: MD110 with public line and ELU32 networking to EEBG. DID number in MD110 is sent to the route to EEBG. This work fine, but when IP-ext. on EEBG is calling out useing MD110 as transit node only main number is showing. I have traced (STUNI) and see that MD110 is not added the...

*BC12 SP5* Is it possible for a acd agent to send acd grp number as a-number? Use NUTRI:ENTRY="agent odn",cnvtyp=1,numtyp=10,trc="dig in odn",pre="avd grp number"; This work when calling to public line, but is it possible to show the same when calling another ODN?

I have 2 LIMs that are connected via QSIG, each of them have public lines. To get the NLOG right I have NUTRI:ENTRY=x,CNVTYP=2,NUMTYP=2,PRE=00; on both LIMs. Use BC11 is no problem, but use BC12 I don`t get 00 in front of the public number when call is transit to the other LIM. 00 is DEST for...

Anybody have route parameters for normal public line in Saudi Arabia? Do they use TLP30 CAS or ISDN?

Anyone know have to get access to the 3rd Party menu tab? Cordless Phone Manager: Menu path: Service – Subscription data – Change PIN Air-protocols: DECT-GAP/CAP Mode: Init mode The problem is that I don`t have Change PIN in the menu. I use CXCNB 201 56/6 R3G

How reset IP-phone DBC 4425 back to factory setting? //Trident//

When was MD110 Release BC12 released in the UK ??

Anyone have experience with? TMLOAD Time for automatic gatekeeper discovery and IP load distribution routine. I have 4 ELU31 cards and need to use load distribution. 120 IP-phones. //Trident//

Anyone have experience with Genesys and MD110 BC12? If so witch country?

How can I change IPAD value on NIU2 card? I use writeic in niux, but got it wrong

Case: A call B. B pick up the IP phone. Sometimes it takes 3- 10 sec. before A can hear B. There are no prioritet inn the LAN. Can QOS and bad bandwith case this problem?

Anybody have parameters for IP-trunk with ELU32? ROCAI: RODAI: ROEQI: RINII: RIANI: RODDI

I have problems with Dialog 4222. The telephone works fine in 5- 10 min, then the clock is missing and the phone get blocked. If I unplugged and plugged the phone it works again. If I use Dialog 3212 on the same EQU there is no problem. MD110: BC12 SP1 and ELU28/3 R5A.

How can I change IPAD value on NIU card? I use writeic in niux, but got it wrong