Search results for query: *

Hi If I call a mobile then my call follows the correct ARS etc and goes out on Route Pattern Pref 1 as it should If I put a call fwd on and for some reason the call goes over Pref 2 I have checked CORS etc and all looks good Any ideas anyone please ?

Anyone out there ever connected Avaya switch to Mitel SX2000 via a ip-trunk One of my customers is asking if ip-trunking will work between these 2 switchs regards 4merlucent

Is it possible to replace the TN2400 while the cabinet is still powered up? I have only ever replaced control cards while the system is powered down but was just wondering why control cards are not "hot swappable

I have a V10 G3r connected to a Vega Digital Gateway via Qsig, this connects to a soft pbx and services sip handsets The problem I have is that I can call-forward from a handset on my G3r to a sip phone and connect when I call in externaly to the G3r via the isdn trunks But when I try to...

I have checked the documents for the s8710 dimensions (3.4in high x 17.5in wide x 26in deep) and assume that an 800mm x 800mm cabinet will suffice. However I have been told a special "server" rack is required due to the depth of the s8710 severs Can anyone confirm if a standard 800mm x 800mm...

If I "list fiber-link" I get "MISMATCH" next to one of the links, the primary facilities are all "B" apart from 1. Does the mismatch come from the different primary facilites, if so can I set them all to "A" by busying the links?

Hello Please can anyone provide some bullet points about the benefits of updrading to CM media servers as opposed to staying G3 for as long as possible? thanks for any ideas

I will be connecting a Prologic to a VIP voicemail via analog ports, I believe the Prologic needs Mode Code activating, has any one used this before Thanks in advance 4merlucent

When trying to upgrade the firmware via Installation Wizard I get message "TFTP - Server is not reachable" I get this same message when trying via CLI The G250 can see the network as I am logged on via the network, and I have upgraded the G700 firmware of the main system OK Do I need to...

the docs say to use USR sportster v.34, is this the case or can I use any modem? I've got a multitech ZBA modem that drops my connection before I can get a login prompt. I have tried 3 different modems now (2 different manufacturers) none work Do I need to change anything on system-parameters...

Can anybody tell me what I would need to deploy a couple of remote handsets (4602) to connect to s8300/G700 CM3? Does SIP need a CCS proxy server? thanks for any help

If I need to change the IP addresses on my s8300/G700 is there a procedure I should follow, or can they be changed in any order? (MGP, VOIP, stack, ICC and gateway) thanks for any help

I have attempted to reconfigure my IA770 by h.323 trunk instead of CWY1 board and analogue setup, my trunk grp and sig grp are in service but I can't call audix. I have installed software from /usr/CHIA but MESSAGING shows as down when I run systat Anyone done this successfully?

Does anybody know how to install an rpm patch (IA770) on an s8300? thanks

If I call the individual ports I connect but get "re-enter touch tones" message If I call the hunt grp pilot number I get busy seems to just be a mismatch in my adminstration but can't see where. I'm not sure about comm interface processor channels admin as data modules not supported on 8300...

I have had to remaster the disk on my s8300, I've done this OK, logged in as craft/craft01 and restored my translations and license file, restarted, now I can't login If I telnet to 192.11.13.6 I can login using my previous login, but when logging into SAT I get "login incorrect" on every login...

I have just changed the IP address range on my voice network & s8300 server, can telnet to 192.11.13.6 and connect via ASA to that address, but cannot connect to web browser Has anyone experienced this before?

Iam trying to set up a 3616 wireless ip- handset I can set the ip-address, subnet mask and default gateway, but I cant see any options for setting the tftp ip, call-server ip, call server port and vpp ip anywere in the admin menu Anyone out there set these up before Thanks in advance

Can Anyone help please We are trying to push one of our customers to upgrade from G3r v10 to S8710, there was a document from Avaya out a while ago stating the official end of support notice on Gr3. Does anyone know were I can find this please, tried looking everywere.I am compiling a paper on...

I currently statically address my handsets as I only have 10 but would like to try DHCP I have read the LAN administrator's guide but have a few questions: As I will not be using a TFTP server, do I keep my firmware on the actual s8300? What does MCIPADD refer to? Any pointers would be...