Search results for query: *

Does anyone know where to disable the CO Admin Audit of the VAS-ID.

I have looked at thread798-1289561 and my problem is that I have MM on a 81c and the message is every 1 min; this has been going on for sometime now and I have sysloaded the switch a few times since. I only have one active AML port which is for MM. Does anyone have any suggestions where I should...

I HAVE EVERYTHING SETUP CORRECTLY FOR CALL FORWARDING BUT MY PROBLEM SEEMS TO BE NO FREE LINES WHEN DIALING OUT WHEN THE CALL IS FORWARDED OR TRANSFERED. I HAVE A PRI WITH 20 DIDS; LINE 145 THRU 164. THEY ARE ALL TARGET LINES. LINES 001-023 ARE ON PRI-A BUT ARE UNABLE TO GRAB A UNUSED LINE TO...

Does anyone no what version 30NdG00 is? Thanks,

Is it possible to move everything built on a line card to another card? Without moving every TN one at a time.

I think I have one that will stump most of you; I have ICS 4.1 system with a PRI programmed for NI2. When I forward a desk phone to a cell phone and 4 digit dial that ext. from another set on the system the call is forwarded out of the switch correctly and call is completed to the cell phone...

I would like to know how to disable long dialing on specific set. Does anyone have a suggestion?

Is it possible to setup a voicemail box on a 2250 console?

Over the past 2 days I have had some of my printers LPR ports just disappear. It appears to only be happening on two specific subnets. The next day I have to go back in and recreate the ports. The printer names are still there. All my other printers seem to be fine. There is nothing I can see in...

Does anyone know where I can change the which CLID entry my 2250 pulls?

Does anyone have any suggestions where my problem might be? On my attendant console my LDN Data for LDN0 is 7000 and my ANI_DATA is ANAT 353 AND ANLD 7447; when calls are placed caller ID is showing the 7000 LDN and I need it to show the 353-7447. Anyone have any suggestions.

Is there anyway to configure a ACD Queue to forward to another number after a specified number of rings? I know I can NCFW but that treatment does not allow the queue line to ring.

I was wondering if anyone knew exactly what card this BERR error is mentioning? Thanks, % BERR704 EXC 0: Bus Error in ISR % SR=0x2700, PC=0x10f35c32, Addr=0xb000c140, SSW=0x105

Anyone know what the NTDK26AA (Option11E to 11C Convertor) would be used for? I will be performing a upgrade from a 11E to 11C Succession 3.0 soon and Nortel shipped that card as well. I can't seem to find a need or a use for it in my upgrade. Anyone have a clue?

Does anyone know where I can get my hands on a configuration book for a SEB II Modem?

I have a path built for external transfer setup on line028; these are centrex lines which require a 9 to dial out. I have configured line028 as PUBLIC but when I call the CCR and press option 5 (external transfer)I recieve a message that states that the line or line pool is not configured for...

Does anyone know how to completley wipe out previous programming of a Norstar VoiceMail system version 4.0. without having to reload the software.

I have centrex lines coming into the MICS 4.1 which require a 9 for dial out access, but when I push intercom I have to dial 9 and then I'm transferred to an available line in my pool and I have to dial 9 again. Does anyone know how I can strip one of those nines off.

Has anyone out there experienced any problems with forwarding your deskphone to a GSM cell phone?

When I redirect a line to an external number (mobile#)it rings the mobile once then gives a fast busy. Anyone have any suggestions?