Search results for query: *

Hi All, Major issue with 11C running 23.35 Unable to run an EDD since.....February. It fails after the CONFIG tries to write to disk. ~~~~~~~ DB SEQ NUM = 3823 CONFIG EDD007 ~~~~~~~ Looks like we can't write to c:/u as LD 117 update data doesn't work either. There are obviously a lot of...

Hi All, I have an issue with zone bandwidth management for calls to multiple zones. Scenario: Zone 1 - Head Office Zone 2 - Main Office Zone 3 - Branch Office The WAN link between Zone 1 and 2 is 100MB The WAN link between Zone 3 and 1 is 10MB The WAN link between Zone 3 and 2 is 10MB...

Hi all, Is there anyway to stop all the LOG and QOS messages from displaying on the terminal when using telnet to a signalling server? I have a script that runs on prints some commands but the messages that spit out on screen are interrupting the data flow and it fails. If I could suppress...

Please can somebody explain this to me. Whenever somebody with a remote destination profile calls inbound to a route-point on the CUCM, from the same number that is associated to their RDP, we get a busy tone. As soon as I take the external number out of the RDP and call inbound to the same...

Hi, I have an issue where my server somehow is running with the RAID controller disabled (in BIOS) and where there should only be 2 drives (C and D) I can see 4 drives in Windows (C, D, E and F). I have 2 disks in the server. Now I need to enable the RAID controller and get the mirror back in...

Hi all, I have replaced the octopus cable and even INI'd the switch but the 3 TTY's still are completely dead. I can Rlogin and have rebuilt the TTY's with no luck. The terminal settings are fine too as the same setup worked on this switch a week ago. Is there anything else I can try before...

Hi all, I have a problem that has occurred on every CS1KS/M rls 4.5+ (SSC, pure TDM) I change the IP addresses for active and inactive ELNK fine. Can ping, can Rlogin, all good.... Then configure SNMP traps. Alarms trigger traps correctly, I can receive them fine, but the trap states that...

Hi all, I am tearing my hair out. I have a 5.5 system sending alarms to TM fine. Then there are two other 4.5 systems configured correctly but TM doesn't receive their alarms. I'm just looking for them in the Alarm Notification window. I have tried Meridian1, CALL_SERVER and even...

Hi all, Does anybody know of a way to tell if the SNMP alarm subsystem is still alive? Is there some kind of heartbeat alarm that I can receive by SNMP at intervals? I want something more specific than up/down ping monitoring. I was thinking of using the DTC001 alarm. Does anybody have any...

Hi all, Does anybody know whether the text defintions that display on the screen when you do an >ERR DTC103 (or any other error code) are stored on the hard-disks anywhere in plain text format that I can import to a CSV or TXT file? This is the info I'm talking about > DTC0103 System is...

Hi all, I am trying to connect TTY1 on an 11C to a terminal server that has an RJ45 interface on it. Basically, I need to know the pinout of the Port1 head of the 3-headed SDI cable. I tried a standard RS232 pinout to the RJ45 but the console doesn't appear. I have tried using a null-modem...

Hi all, Silly question but I can't remember or verify at the moment. Is the 11C, 3-headed monster cable male or female on the DB25 end? I need to buy cables and adaptors before I go to site and can't remember what the ends are. TIA

Hi all, I may get scorned for this, but is there any possible way to get the admin/tools passwords reset without an install tape. The tape has gone missing and somehow, nobody knows the password, even the current provider! I have tried all the default passwords (even customer and auxadmin!)...

Hi all, Has anybody had any luck with these new transceiver modules manufactured by Mertek? I am getting increasing input error counts with no collisions on my elnk stat. >ld 137 CIOD000 .stat elnk ELNK ENABLED Ethernet (qu unit number 0): Host: PBX_ELAN Internet address: 172.17.30.244...

Help, I was logged into the system (CS1KE 5.0) as admin2 and printed some reports. I then put the wrong password into OrderPro and now I can't login. I have waited the maximum 4.5hrs for the FLTH. I get OVL111 IDLE 0, then when I <cr> to get a login prompt, I login with admin2, but it keeps...

Hi all, Does anybody know where I can get a free mlink tool to make one phone call another phone and answer the call? I know you can use mlink, but it is very cumbersome. Is there another tool out there that I can use to make these 'real' calls?

Hi all, Is there a way to force disconnect a user from a terminal session within the SS OAM> shell? Or can you disable these PTYs? oam> 21/08/2008 11:22:11 LOG0004 tLogin: User <admin2> has logged into the system. who FD DEVICE USER ADDRESS 3 /tyCo/0 nobody 9...

Hi all, I have an issue on a CS1KS 4.5 with only 1 MG. For some reason the REMOTECAB3 hostname keeps appearing in my host table and I would like to get rid of it! How do I remove that record from the dbase? => prt host Call Server/Main Cabinet ID Hostname IP Address 1...

Hi all. I am getting this error when trying to register a 2050 to a CS1KS Rls 4.5... LOG0003 VTM: ITS2005 Terminal's node ID/TN configuration is corrupted Can anybody point me in the right direction? I have it configured to connect to port 5100 on the CS

Hi all, Is it true that there are different 'versions' of TM available for different purposes? I am hearing that there is up to 3 versions, one for end-users, one for distributors and one for enterprise.... Can anybody either confirm or deny this rumour? It is obviously a licensing mode...