Search results for query: *

Hi, all! Please, how to set "presentation restricted" on analog or digital port? For example, we have ext. number (local port) 3543, and for external calls through PRI EDSS1 we should have in SETUP message Calling Party Number (CgPN)=3543 and CgPN Presentation Ind.=Restricted not Allowed. What...

Hi, all! We unmount HDD with MD110 backup from HDU7 board, connect the HDD to PC ATA-bus. Windows detected the HDD but not its file system (MD110 backup), read that the HDD is unformatted. May be we should use Linux? Or another way to read/write the HDD. Thanks.

Hi, all! Can we use Dialog 4222 with MD110 BC9, CNI76? If yes, what ITYPE we shall set? Thanks

Hi all! The phone is parked: susip:dir=5909; STATUS INFORMATION AT 15:19:13 21FEB08 DIR TYPE TRAFFIC STATE/PTR LINE STATE/PTR DIV STATE ADD INFO 5909 ATS PARKED #0275 BUSY #03D6...

Hi, all! We have BC9, and CDIDP: DIR---DIV 1000--1001 it works on no reply 1001--1005 it's not, i.e.: We call 1000, phone rings, no answer, after a while calls rerouted to 1001, phone rings, no answer, but, after a while call is not rerouted to phone 1005. How can we solve the problem? Any...

Hi, we installed licenced WinFIOL and Tools 7.0 (Build 35), choice Complete installation, then configure Target: APG 30 (AXE) APG 40 (AXE) CPP (NCLI) ERIPAX Generic NE IOG11 (AXE) IOG20 (AXE) IOG3 (AXE) OSS (AXE) OSS (TGW), but, where is MD110 ????????

Hi, is Ericsson IP-interface for IP-phones proprietary, or we can use IP-phones from another vendors? Thanks.

Hi, all, simple question - if md110 works as only transit station, e.g., 3 PRI EDSS1 - the law of 11-12 calls in 10 seconds and no more or alarm, works or not? Can it carry the load upto 100% ? Thanks

Hi, all! People say, E/// recalls PU4DC. What for? Or it is only for some markets (Russian, for example)? Thanks

Hi all! BC9 CNI76, modem BYB2424 in MAG0. History: 1. Access through modem was right, worked. 2. After failure MAG was changed from LBP17 to LBP20. 3. Access through modem is not right, not worked at all. STUNI/STTSI/STRAP gives NO SIGNALS FOUND . Program units TWP2, ICM were restarted...

Hi, can the Conference Leader selectively disconnect member(s) (keeping all others connected)? Thanks

Hi, all! Can we use LBP16 magazine not only as ICM but PSM? To install LPU5, IPU and so on in BC9? Thanks

to whosrdaddy et al A question about copyright - can we reproduce some ourselves edited topics from this site at our private sites not for sale edu only? For example, in word version, converted to html?

Hi, how can we regulate A-number presentation (displaying) on system digital phone display? Digital phone connected to ELU28, BC9 CNI76. The matter is that we receive IAM message with two fields - Calling Party Number and Generic number. The station (BC9 CNI76) displaying Generic number. Can we...

Hi, all! The question: is it reasonable to give SFCEI command before dump (DUSYI) ? Thanks.

Hi, all! BC9, CNI76, 1-LIM system, single (non-duplicated) control system, 2 TMU in LIM: We had alarm "324 FAULTY TMU BOARD" on one TMU & "62 BUFFER TRANSFER HARDWARE FAULTY", FTTDI, FTMDI give NOK, well, BLDBI, CNBOE for faulty TMU, second TMU is O.K., but "62 BUFFER TRANSFER HARDWARE...

Hi, Preamble :) : when we go off-hook and then no dial, the system waits 8 seconds, then sends three-tone. Question: is it possible to set this timer to, for example, 16 seconds? Or this is prohibited for PABXes as class due to common resourses limitations? Thanks, HIREI

Hi, is there a service to reroute incoming call to local MD110 number by pressing the key on your DBC phone just watching the A-number blinking on display (in the on-hook state, of course). Thanks.

Hi, is there Alarm Clock Service in MD110??? I know in BC9 no such service. May be, in another versions? BC10 - BC12? Regards, HIREI

Hi, pls, how to read ECF Number from MD110 terminal? MD110 BC9 CNI76. Command SUSIP gives us the fact the ECF is used but not the external number. For Follow me we get the fact and the number: FME=DIR in Additional Info. Thanks, HIREI