Search results for query: *

Hi folks, Is DECT R3 system compatible with CM6 or CM7 ? My customer has large DECT R3 installation on CM4, and thinks about upgrade to CM6 or CM7... Best regards, The Curious

Hi folks, Is it possible to find out if ring generator on ELU-A is working or faulty ? Would any tracing, warning logs or extension supervision from BMS show anything if ring generator is faulty ? In my case BP50 behaves like this: Extensions from ELU-A can call digital extensions. Digital...

Hi folks, I have an installation where BC12 SP6 system is connected to ISDN BRI lines via TLU79. ISDN lines have bad quality, and there are lot of alarms which appear and disappear in a short time (local telecom claims that "everything is fine" with their lines). Alarms are: 269 DIGITAL TRUNK...

CM4,G650/S8720, H.323 IP phones - models used are 4610 and 4621, computer network is based on Cisco 3750 switches. Customer run out of ports in ethernet structured cabling, therefore they connected a cheap, non-managed switch to PC port on IP phone. 4 computers are connected to non-managed...

S8400 Server / G650 gateway / CM4.0 Save translation command does not work, response from system: MSS Error Encountered It is not possible to access server from web interface. As far as I know, this should be a problem with flash disk on S8400 board. There is special patch that tells you if...

Hi people, I have a customer with CM4 system, having old IP DECT ( RFP32 base stations, 3701 and 3711 handsets). Is it possible to upgrade this PBX to CM6 and keep the existing DECT system ? Best regards, The Curious

CM3,S8500/G650 IP phones 4621, 4610 ISDN trunks When you make outgoing calls over PSTN trunks, and called party does not answer, telephone number does not appear in redial list on IP telephone. In which way should I continue my investigation ? Feature settings? Software patch? Software on...

Existing System is S8400/G650, CM4 They now want upgrade to CM6 and they want SIP. As far as I know, S8400 must be replaced with S8800, because S8400 is not supported in CM6. What about SIP, do they need additional server for SIP? Thanks, The Curious

Hi folks, I have experience with Communication Manager, on the other hand Definity is an unexplored area for me. Yesterday I went to a site where Definity G3,Version 11, is installed, to do some moves-and-changes. I found a proper serial port, connected my laptop(Windows XP, ASA 5.2...

Hi people, There is a hunt group with a queue, members of a hunt group are also members of a pickup group. Extension 111 receives the call from a queue. A little bit later, someone is calling extension 111 directly, using DID, so the second line appearance on 111 is ringing. Now extension 112...

S8500, CM3 Pccard backup always fails. I tried to format card without success. Please take a look at system response below: pccard_format: Card to be formatted with filesystem: All data on card will be destroyed mke2fs 1.27 (8-Mar-2002) pccard_format: 0: PC Card format completed successfully...

I need to make reload of LIM remotely. If I want to make a reload of LIM, procedure is clear: 1. Block the LIM for traffic by BLLTI 2. Do LALRL to reload a LIM But, what can I do if modem connection goes through LIM that should be blocked ? If I block a LIM and stop the traffic, I wouldn't be...

CM5, 9610 IP telephone, telephone software 3.0 1. Caller ID If I define 9610 as 4610 telephone - caller ID is working. If I define the phone as 9610 - caller ID is not shown. I would like it to be administred as 9610, and to keep caller id...Possible ? 2. Light When the phone is ringing,red...

HI, I want to change firmware on SPU2 ROF 137 5416/1. Now the board is having firmware CAA 158 0006, and it is used for voice compression. I want to change firmware to CAA 158 0003 and use it for voice mail. In the other words board VCU2 should become board VMU. Is this possible? Is there any...

I made a backup of translations on compact flash card. External flash drive is attached to S8500, CM3.1. Backup was OK. Several months later I went to same site. Compact flash was empty... Where did I go wrong? Are there some special settings I should take care of? The Curious

Is it possible to use softphone as a member of hunt group? Softphone 6.0 SP5 CM 5.1 The Curious

S8400/G650/CM4.0 Personal CO line, connected to another PBX. Incoming calls are working OK. Outgoing calls are dropped after few seconds, both parties hear each other for a while. When I connect analog telephone to wires between G650 and another PBX, i normally make and receive calls...

Hi, Incoming calls to a loop-start trunk should be automatically transferred to one public number, using ISDN trunks as outgoing route. I have defined a VDN number that contains vector, vector contains route-to (dac+public number) unconditionally. Incoming destination of loop-start trunk is...

Hi, System is CM5/S8300 with IA770 implemented. Is it possible to have conversation recording ? Best regards, The Curious

Hi, IP telephone 9610, customer wants to access the public line without dialing "9", just by picking up the handset. Any idea is welcome ! Best regards, The Curious