Search results for query: *

I"m looking for a compatiable server SFP ethernet card solution for mim signal loss connection. I'm deploying a cisco rtr with a Cisco SFP-10G-SR MM fiber connection to a intel 10 gig XF Server adapters which is 10G. But the problem is signal loss between the cisco transeciever and the server...

Can a cisco 6509 cpu spike crashes the device. Making it go into ROM Mode? Added an ip sla to the device and then the device crashed. 877778777987987670 475838776339956950 100...

I have a BGP session with a number peers on a vlan. The subnet is a /25 and I would like to change it to a /24. Will this subnet change restart the BGP session with the peers?

What type of cisco router configurations besides URPF can use to protect or slow down Slowloris attacks

I have a MPLS TE mesh network with OPSF as the link state protocol..All the tunnels are running in area 0...I have also created other areas..Will I run into any issues if I create stub areas with MPLS running on the backbone..

I have a 6506 and I'm upgrading to the 7606 S-Chasis. Will the line cards work in the 7606 S-Chasis? Is everything seamless from one device to the next.

I have PBR setup on several of my routers. But it's not rerouting the traffic at all...currently I have a 10.1.1.0 network on the LAN coming to my router. The normal behavior is routing via the ospf.but I want it to go in a different direction across a T3...Am I missing something..Below is my...

Question 1: I have a 7613 cisco router with two sup 32 engines.what variable determines the running IOS on two active sup engines? Question 2: Currently one of my sup 32 engines is in ROMMON mode, if I load my IOS on the failed engine. A. Will it return two standby HOT B. Will it supercede the...

I want to bundle two T3 using MPPP, but unfortunely cisco guidelines restrict the use of T3 bundling on this router. What other solution can I use besides MPPP? I want combine the two 45mbps so I can get the full use of a 90mbps pipe?

I have a request to do a dot1q trunk between a switch and a server...What are the disadavantages of doing this(spanning tree, broadcasts etc) and what are the configurations for server to do this.... P.S. If I do this can I configure the trunk to be an isolated port or community port?

I'm running ospf in my network and collasping the number of areas..Can I run two area 1's in my network.. For example: Router A is in the backbone with routers configured for area 1 Router B is in the backbone with routers also configured for area 1.. Will I run into any issues with this...

I have a 7204 cisco router with an OC3 card.Currently the rx and tx load is often at 150/155 145/155 during the day..The problem is the output drops is increasing my 5000 each 5 min cpu interval. But last friday the router began to hang, I rebooted it and it started working again..On Tuesday...

I have an OC-12(155mbps) pipe coming from an MPLS cloud into a CE router. What I need to know, what is the maximum speed for 1700 Nortel encryptor or do I need to another encryptor to balance the load. Or is there a Nortel encryptor that can handle an OC-12 pipe?

Hello everyone, This is regarding a stub area I'm trying to configure..Now I have a good understanding of stubbing an area...I curious let me explain.. I have two routers and two switches in area 0... The two routers all have area 0 connections in the backbone, but the switches have another...

My area 0 is doing constant recalculations, but the network is very big...I need a logging or snmp command to narrow down my search for the culprit... Besides log-adjancency-changes under the process, what other commands can I use to point to my syslog server?

I attempting a BGP load sharing scenario in a lab I have...I have three routers...ISP 1 and ISP 2, pluse the CE router... The folling programming consists of this.. ISP 1: int loopback 0 ip address 2.2.2.1 255.255.255.255 BGP 65000 neighbor 1.1.1.1 remote-as 64000 neighbor 1.1.1.1...

I have several 7200 cisco routers with multiple T1, T3 and OC3's on different routers..What I'm trying to determine load these circuits have on the routers CPU... I can determine the CPU load of between a T1, a T3 and/or OC3 connection... I look at the "sh process cpu history"..But's the load...

Hello, everyone...My question is I'm trunking between two cisco 3550 smi switches and I just enabled rip between the switches and the primary switch connects to my router....On my router I have bgp and rip configured respectively....I redistributed bgp into my rip domain and advertised the rip...

Does anyone know the option for forwarders in Bind 9...I attempted to configure forwarders in the named.conf, but the configuration won't accept this option...I'm pretty sure I have the config's right forwarders { 1.1.1.1; 1.1.1.2; }; But I'm when...

I have a html scripting question...I do I write a html form to send an automatic email to people when they fill out question boxes... I have drop boxes for the person to fill out, but I can't import the data in an email and then send it out....It just keeps bringing up the email without the...