Search results for query: *

I need to monitor free disk space on the Cisco CSS11050 running software version 6.10 Does anyone know of a MIB that can do this many thanks

we have installed a new sdsl line with Pipex - their guidelines have suggested that the dialer interface should be set to "ip address negotiated" however we have been assigned a range of ip's one of which I want to use on the Pipex router as we will then be able to route traffic out of one of...

I want to know if there is a source other than the IOS bug toolkit that can be used to check latest Cisco vulnerabilities on their range of routers. I currently have over 400 837s now running the same IOS but I want to run monthly IOS/config checks to make sure they are not vulnerable...

I have two options currently for setting up a new VPN solution. we will have approx 250 users connecting via RAS the options are ISA 2004 or VPN concentrators (concurrent 150) the setup using ISA would be two entry points one box for each - to allow some kind of resiliency. using AD to...

I know this could be in either forum but anyway - here is the problem I have VPNs setup for RAS users - authentication takes place on the ACS box (with AD). users have no problem getting to unrestricted areas on the local LAN. The problem is when they want to access other networks on the...

I know this could be in either forum but anyway - here is the problem I have VPNs setup for RAS users - authentication takes place on the ACS box (with AD). users have no problem getting to unrestricted areas on the local LAN. The problem is when they want to access other networks on the...

I am currently in the process of setting up a VPN solution. I have the firewall currently issuing the IP address for clients when they log in - however I want the ACS to do this job as I can then restrict the access rights for different user groups. set up currently is as follows Client -->...

Has anyone managed to get this working - I curently have mppe working for 2000 and XP machines, unfortunatley I still have 100 or so NT4 machines tat cannot support mppe so therefore I have configured the pix to accept pptp - bu cannot get it to work. Has anyone managed to achieve this? thanks...

I know these three go together - but I don't know how. does anyone know of a doc. that can point me in the right direction. I basically need to configure the PIX so that it allows vpn access which is authenticated on the ACS box ideally using PPTP but with the facility to use MPPE if we need...

I would like to know whether a Supervisor engine II is compatible with an new 4506. basically I need to get hold of another swith for our setup - we have a spare sup engine II card that I would like to reuse if possible (as I don't think I'll have the budget for a new supervisor engine). will...

I need to audit all of the routers we have in stores (around 190) but i need to get the serial numbers - I thought if i did a show ver it would give me the information I need. It doesn't - the routers in question are cisco 837s Any ideas Thanks Steve

We currently have 2 networks that use different methods of Remote access. 1 network uses CiscoVPN client and sets up VPN tunnels (authenticates at the firewall for the tunnel) then authenticates on ACS box before allowing the user onto the internal network. The other uses Windows RAS this...

I am experiencing some problems with our remote branch routers - these are the errors I keep seeing. the IOS version is 12.3.(7)T file c837-k9o3sy6-mz.123-7.T.bin 4856: Feb 9 05:06:06: %SYS-3-CPUHOG: Task is running for (5000)msecs, more than (5000)msecs (100/39),process = Crypto IKMP. 4857...

5 minute input rate 2262000 bits/sec, 457 packets/sec 5 minute output rate 1282000 bits/sec, 477 packets/sec what does this actually mean in terms of bandwidth used and is there an easy way of calculating it. Many thanks Steve Lindley CCNA

I started with this comapny about 6 weeks ago so was still getting used to the setup. Unfortunately the the cerificate used for vpn authentication expired. I am totally new to CA servers and VPNs and IPSEC tunnels so I thought I could just renew the certificate and everthing would be fine -...

I should know how to resolve this but it is causing a lot of hassle. int ethernet 0 I have a 3com switch when pinging from a pc to the e0 ip address it works fine atm0 (dialer1) is the wan port and I can ping from here to most places on the corporate network the problem is when I ping from...

Hope someone can help. I have over 100 sites connecting to the main network via IP Stream - all traffic is encrypted from each site by to tunnels. problem I am having is that - every now and then a tunnel drops - not a problema simple reboot does the trick and it will loadbalance ovet the...

Hi this may be in the wrong area. I currently use SNMPc and was wondering if it is at all possible to montor when a tunnel goes down and to be flagged when it does. we currently have ADSL sites that are connected via IP stream over two load balanced tunnels (from each site) back to our main...

Hope someone can help - I have SNMPc working fine except for the email notifications - for some reason I cannot get SNMPc to send emails based on any events. Does any one have a simple step by step solution to this Many thanks Steve Lindley CCNA

I have a number of ADSL routers on my network, I have been checking through all the configs and have found some routers with 100% utilization, when I dig deeper there are no stats for any of the subsections all appear as 0. A reload always clears the router but I want to know why this is...