Search results for query: *

If I migrate my licenses to the new Presentation Server license server format, will my old servers still work. I currently have 1 Presentation server 4, and the rest of my servers are Metaframe XPE. thank you for any advice Matt

What updates do you have to do to windows 2k to get presentation server 4 to run?

ok, what happens is if you call from location A where the PBX is, it goes to a Fxo on a cisco router, then to the location B. If I call the number (from A), wait a couple of rings and hang up it says proceeding under SHOW VOICE CALLS and the phone on the other end (B) continues to ring for...

3d17h: IP: s=10.54.1.6 (Serial0/0.612), d=10.12.64.1, len 40, rcvd 4 what does the len mean? thanks Matt

I have a location that needs to have traffic going to one specific ip to have priority. How would I do this, the hardware at each end is a cat 5500 with atm interfaces. thanks for any help.

I have some users that work from home fire off batch jobs on the mainframe that run for quite sometime and of course their citrix sessions timeout, and well frankly that is the way it is supposed to be, I don't want people logged on to my servers hours at a time with idle sessions. Is there a...

I have just added a nm-1t3/e3 card to my 3745 and it shows up in show ver as 1 Subrate T3/E3 port but the module does not show up in show int? what the heck?

I have a 3620 with ds3 card that is only getting 5 mbs and it is supposed to be getting 45 mbs. I am going to start a large ftp process - what would would be the best way to monitor the line - show ? - debug ? thanks Matt

Ok, I have a 3725 with 8 port ima card and 3620 with a ds3 card. I want to switch the two cards between the routers. I tried it once and failed. The cards came up and worked, but the router that now has the ima - the 3620 would no longer route the packets? I could not get to any of the...

I have been trying to setup a vpn, and I can not figure out how to bring up the session. Here is one router config, I will do a reply with the second. Current configuration : 4699 bytes ! version 12.3 service timestamps debug datetime msec service timestamps log datetime msec service...

Is there anyway to move equipment to a new data center without changing ip addresses? Is there a piece of Cisco equipment that would help with this? I have a good sized budget so... thanks Matt

Is there some place to look up the thru put cabablities of a router - basically how much traffic can they route? Like 1.5 mbs - 45 mbs? Maybe there is not an exact amount but perhaps what is recommended for each series of routers? thanks Matt

I have two 1700 series routers and I am trying to route thru the ethernet interface, then thru a vlan ip address that i gave to the ports on a wic 4esw card, and it doesn't seem to be working. thanks Matt

We have a ds3 and it has 62 pvc's. The ds3 is supposed to be 5 mps cir and burstable 45mps At most we achieve 5mps and it never bursts above that. I have this set on one of the pvc's. Is this correct, or do I need this set on all the pvc's? vbr-nrt 43952 5521 900 or is there something I need...

I am not completely familar with BGP but, I have 5 routers in BGP AS 65054 and then another group of routers connected to one of them via BGP AS 65000. Is there a way I could have this router advertive a route to the systems across AS 65000 and no to the rest of the 65054 routers? Thanks you

Here is a 2600 I installed the ima card in Cisco Internetwork Operating System Software IOS (tm) C2600 Software (C2600-JS-M), Version 12.1(3a)T1, RELEASE SOFTWARE (fc1 ) Copyright (c) 1986-2000 by cisco Systems, Inc. Compiled Fri 28-Jul-00 01:41 by ccai Image text-base: 0x80008088, data-base...

What if you are on your second test of the CCNP and your CCNA expires? thanks Matt

I have a main 3620 router that routes to our other hq and offices on a ds3 using atm pvc's. I can not get from any of our small offices to anywhere on the other hq network other than the main router. The small offices can get to each other though. Here are some trace routes. Tracing the...

The server crashed with a stop error, the only way I could get the server back was to use the recovery console and replace the system file in the config folder with the one in the repair folder. Now the second volume which is a group of spanned drives has no volume label and says failed. The...

Is there a way to limit bandwidth from and to a specific ip with a cisco 7000 serious router? thanks Matt