Search results for query: *

Hi, I've got an old NT4 domain and a new 2003 Active Directory domain, they run on different subnets and are connected via RRAS (PC with 2 NIC's). I've installed backup exec on the new domain and in order to get backup exec to use it's remote agents (Doesn't work with user defined shares) I...

Hi, We originally had an NT4 domain, I then put in a new AD domain on a different subnet to run along side, connected via RRAS. The old domain can browse the new domain and all PC's, but the new domain only see's a couple of PC's on the old domain despite the fact that I have a bi-directional...

Hi, I setup OMA at our office on Exch03 here and it works a treat. I did the same thing from somebody else and it didn't work. When I tell the mobile device to sync via GPRS it connects and shows me the emails and contacts coming down and then completes as SUCCESSFUL. However when I go the...

Hi, Just got a new server, plumbed in a VS80 DLT drive, 642 array controller and a bunch more memory. Just fired it up and it won't boot from the smartstart CD, the CD drive spins up and the light comes on but thats about it. Additionally the array controller initialises and I can use the...

Hi, I'm trying to use RRAS to forward all port 25 traffic to a different PC on another subnet. Setup is below DSL-DSL ROUTER - RRAS PC 2 NICs 192.168.0.1 192.168.0.5 192.168.1.2 The 192.168.1.2 NIC then connects to a cisco router 192.168.1.1 which has an interface of...

Hi, I've got 2 domains on seperate subnets, one 2000 mixed mode, the other NT4. On the 2000 PDC emultor and the NT4 PDC I entered the following into their lmhosts. nnn.nnn.nnn.nnn. #pre #dom:respective-domain-name The router between allows ALL traffic Both subnets can ping and browse each...

Hi, I have two 2000 DCs, how do I find out if they are running in native or mixed mode? Cheers

Hi, I've setup an RRAS DOD to connect to a remote router. My router local IP 192.168.255.248 Remote router external IP 213.134.131.nnn Remote router internal IP 192.168.1.nnn DOD called VOIP is set to connect to 213.134.131.nnn I've added a static route for the DOD as follows Destination...

Hi, I have 2 domains on seperate subnets connected via a router. Both can ping each other happily yet I can't get them to see each others domain via network neighborhood/places. One is a 2000 server with AD, the other is an NT4 server in its own domain. On both I've amended the lmhosts to...

Hi, I have inherited an AD domain. On the domain every time somebody logs on they get assigned a default gateway that I would like to change. Only trouble is I don't know where it's coming from. The netlogon share contains nothing and I couldn't spot anything obvious in the AD config. Any...

Hi, I'm replacing an NT4 RAS server with a win2k one. On the new server I have configured a DOD interface to use an Eicon BRI modem to connect to a remote site. When I try to do a ping -t through the LAN to the new server the ping responds for a few seconds then goes to destination host...

Hi, Setup a win2k RRAS server to deal with incoming users (Dial up) and a dial up connection to a remote system. Users can dial in and I can connect to the remote system fine yet i can't ping it. I tried to add a static route in the console but it wouldn't let me specify the gateway. See...

Hi, On a new AD domain I have created 2 security groups, one local one global. However, when I come to make either a member of the other they are not visible to each other. I've come across this before and worked it out but I just can't remember how I did it. Any suggestions? Thanks in advance

Hi, We've just taken over a new company and there exhchange server has NO backup. Plumbed it in, started it up and it failed to load the exchange directory. Further investigation has shown that the priv.edb, pub.edb and dir.edb are missing!!! What could cause this and is there a way back...

Hey, We have just taken over another company who do not have a backup of ANYTHING. They just lost there best salesman who deleted all of his proposals from his mail account on the way out. Is there any way of getting back this data without a backup (I Know I'm reaching here). Thanks

Hi, I think one of our exchange administrators is abusing his power and reading users inboxs. Is there a log somewhere where I can identify what he's been up to? Cheers Steve