Search results for query: *

Good Afternoon All. We need for an outside host to send data to an internal host thru TCP ports. I see the htcnt for the defined ACL incrementing and the log shows "%FWSM-7-302014: Teardown TCP connection" on both firewalls when using traditional one to one static NAT. But for some reason the...

Good Afternoon All. Hopefully someone can provide direction on this issue. I'm not a phone expert and we just inherit a Nortel Option 11 PBX at this one site. We're having a strange issue. Extensions that were working configured previously and that were working properly all of a sudden stopped...

Good Afternoon All, I'm not a phone system expert and I'm hoping someone can point me in the right direction. In one of our sites calls drop randomly and it happens in both inbound and outbound directions. Our Telco says the circuit looks clean and Avaya says it's a Layer 1 issue. I've done...

Hi All, Hope someone can help me with this one. As I've not familiarized with Cisco stack configuration I got a pair of 3750's that are currently stacked and due to some changes on the network design. They'll need to be unstacked. My question is, what would be the proper process to remove...

Hi All, Hope someone can help me with this one. We have the following network configuration: ISP1 Router ISP2 Router | | Cisco ASA 5510 Cisco PIX 506 | Cisco Switch 3560 What we are trying to accomplish is to use...

Hello All, I'm not a fiber expert and I'm hpoing someone can point me in the right direction. I have 1000LX fiber trunk between 2 3550 switches. This trunk link goes into err-disable state quite oftenly. The reason I get on the syslog is %PM-4-ERR_DISABLE: link-flap error detected on Gi0/1...

Hi all, I have a question on regards to an ACL. Is there any difference between the following ACL commands? permit tcp any eq www any permit tcp any any eq wwww Are they redundant commands? I see similar command throughout an ACL, but with different port assignment. I just want to know if...

Hi All, Hope someone can help me out on this one. I have the following: -3 Distribution Switches (3550’s) -4 Access switches (2950’s) -6 VLAN’s (13,14,15,16,17,18) which span all switches. Intervlan routing is working flawlessly, but I need to lock down access to VLAN 13. Basically VLAN 15...

Guys, Is it possible to move mailboxes from one forest to another? If so, what would I need? Currently I have to seperate forests with trusts and one exchange server servicing both forests, everyhting is working fine. I will be adding a new exchange server to the forest that doesn't have one...

Hello Everyone, Can I have to different forests in the same network address? and Would I be able to create trusts between the two forests? Thanks in advance. Rocket.

Hello Everybody, I have a situation and I would like to share it with you, hopefully someone can shed a light on me. The current configuration is as follows: Location1------------T1 PPP------------Location2 2003 AD Forest1------------Trust------------2003 AD Forest2 2003 Exchange Site1 (One...

Hello all, We just got an Cisco ASA5510 and we have configured for internet and dmz, and that's working fine, but I tried to configure VPN client access based on cisco document and I get the following Info messsage when I try to configure the NAT (inside) 0 access-list comand: INFO: Outside...

Hi All, I think this might be a dumb question. I'm trying to configure a point point T1. I have two routers one at each end and both have the WIC-1DSU-T1 card. When I enter the service-module framing and linecode commands in the interfaces configuration mode. I go back and do a Show Run and I...

All, I added a debug icmp trace command to my pix and notice the following messages. 444: ICMP type 24 (code 124) 99.99.99.148 > 88.88.88.36445: ICMP type 80 (code 255) 10.1.1.14 > 10.1.1.1 446: ICMP type 24 (code 124) 99.99.99.149 > 88.88.88.36447: ICMP type 80 (code 255) 10.1.1.14 > 10.1.1.1...

Guys, Hope someone can explain why this happens and how to fix it. I'm in the process of creating a new AD strucutre for our company Operations Center, but I noticed the event below on the newly installed domain controller. ------------------- Event Type: Warning Event Source: LSASRV Event...

Hello Everyone, Hope someone can explain why this happens and how to fix this. Recently we relocated a remote site office into our corporate building. So now I'm trying to get rid off the site to site VPN config that is in place on the corporate site. The problem is when I try to delete any...

Hello Everyone, Hopefully someone can clear these questions for me. We currently have the following: - domain1 (hosted with ISP1) - domain2 (hosted with ISP2) - one internal Email server (Exchange), accepting emails for both domains. I've noticed that we have the same MX Record and A...

Hello Everyone, Hopefully someone can clear these questions for me. We currently have the following: - domain1 (hosted with ISP1) - domain2 (hosted with ISP2) - one internal Email server (Exchange), accepting emails for both domains. I've noticed that we have the same MX Record and A...

Hello Everyone, Hopefully someone can help me out with this one. We are currently having an ongoing issue where outside senders, receive the following NDR: Your message did not reach some or all of the intended recipients. Subject: SUBJECT Sent: 4/4/2006 8:50 AM The following...

Hi Guys, Hope you can help me with this one. I'm trying to connect to my network thru VPN connetion using the following configuration: - Cisco VPN Client 4.6.02.0011 - PIX 515E - Users authenticate thru RADIUS server (Behind firewall) - Using class A ip addressing pool I've configured the...