Search results for query: *

I currently have a IFC=ESGF TIE connected to a VOIP server. Dialplans show up correctly, however names do not display across. Under RCAP, I cannot set ND2 or ND3 with this IFC type. Is there an alternative solution to this? Or a recommended QSIG IFC ? --- Andy Pham, ACS/Life Safety IT...

I currently have a Magix system in Hybrid mode with 4 POTS lines and 1 PRI. However, I'm not sure what the best way is to program the system. 1. We want to make a button for each POTS line so when calls ring in or put on hold, a person can pick up the flashing line from any phone in the...

I am connecting an M1 Opt 11 to an Asterisk VOIP server using ESS5 over PRI. On a tie call, 1. We are getting name display and correct 4 digit DN from the VOIP server to the M1 over the TIE. 2. Calls from M1 to VOIP server are sent as 10 digits with NO NAME (like it is sent to the PSTN) over...

Does anybody have a full listing of the Audix mode codes? --- Andy Pham, ACS/FS-IT Honeywell International, Inc. andy.pham@honeywell.com

We currently have Meridian call park zones 71 thru 79. There is a IP PBX on premise tied in via T1 tie line. What needs to be programmed on M1 side to enable the TIE access to the parked call? --- Andy Pham, ACS/FS-IT Honeywell International, Inc. andy.pham@honeywell.com

We are having an issue with CLID not passing through if a call progresses through the following method: *** No Originating # Passed per LD 80 TRAD if... Caller 612-555-0000 -> ISDN PRI Trunk -> Meridian Mail AA -> Ext 123 -> CFW to Outside cell phone # over same PRI trunk = NO CLID ***...

I need to provide voicemail from a central site running Legend 7.0 with Audix and a tie line to a small office with a Nortel system. We would like the Nortel to use the voicemail at the Legend site and have it send call calls to 2770 (VMS number) and get the standard Audix mailbox. Despite...

I have a tie line going from Meridian to a Definity. Meridian ---> Definity displays external number (e.g., 516-555-1212) Definity ---> Meridian showing internal DN (e.g., 1212) How can I configure the Meridian to send internal DN to Definity on internal calls and external CLID on external...

I am getting frame slips on my TIE trunk due to the fact the Nortel is Node Type is User and Tie PBX is NET. Under NI-2 interface, SIDE prompt is available to set as either USER or NET. I've tried both DMS100 and 5ESS and that prompt is not available. Is this setting hidden elsewhere...

Outgoing calls from Asterisk VOIP side to OPT 11 rls. 25.30 only sending last 4 digits. PRI signalling info is showing everything, example: 818004466444, only 6444 is being sent which is last 4 digits Set up TIE of OPT 11 rls 25.30 TO ASTERISK VOIP SERVER Interface: TMDI PRI NI2 ESF/B8ZS...

Brand new NTRB20AA TMDI card in Option 11c Rls 25.30. I'm trying to add a PRI TIE loop to a Cisco 3600 series router for VOIP. Add PRI Card: LD 17 REQ CHG TYPE CFN CEQU YES PRI 04 Add D-channel interface: LD 17 REQ CHG TYPE ADAN - ADAN NEW DCH 05 - CTYP TMDI <--- get SCH5590 error This is...

Does anybody have any pinouts for an Option 11C T-1 Amphenol style connector to DB15 CSU ? The Nortel P/N is NTBK04AA and it is described as a 1.544 Mbyte Carrier Cable. Thanks. Andy andy.pham@honeywell.com

I have an Option 11c rls 25.30. Is there anything special I need to do after inserting the card into the switch? We are trying to add Caller ID to some of our 500 sets.

I'm running a Magix 3.0 with Intuity R4.4. When callers call, leave VM, hang up, the Audix doesn't hang up. Once the caller hangs up, it hangs onto the line until the timeout threshold ends. Is there a Disconnect Supervision setting on Audix? I am 99% sure the Magix knows the line has dropped...

I am installing a MultiTech MultiVOIP 810 on my Option 11C. Here's what I've done: 1. Created (8) 500 type lines on my switch and built a hunt group. Make outgoing calls GREAT over VoIP. 2. Need to set up CDB or something and assign a DID range to pass digits to my VOIP on incoming calls. For...

I am not able to change my Merlin Legend CKE4 6.0 into Hybrid/PBX mode. Is there something I'm not doing right? Both WinSPM and the MLX-20L beeps at me when I select that mode. I have tried to factory reset both physically and by software. Please advise.

I am trying to set up a Merlin Legend R7 CKE3. For some reason when I insert the 012 Basic Telephone Module cards, I cannot get dialtone. I have two of them and neither of them are providing dialtone. If I hook an analog set into one of the modules, I hear clicking and then dead air. If I call...