Search results for query: *

My new e-mail server is Exchange 2003 SP2. My legacy server is Exchange 5.5 . They coexist in the same domain. The Exchange 5.5 server is the one facing the Internet. Users are slowly being migrated to the 2003 server, and eventually I'll decommission the legacy (5.5) server. Exchange 5.5...

I was on 6.3(4) and upgraded to 7.0(1). I also added a DMZ interface, but it is not configured and basically disabled (shutdown). I now get: %PIX-3-305005: No translation group found for tcp src inside:65.59.207.13/80 dst outside:208.x.x.x/2671 and %PIX-3-305005: No translation group found...

I'm trying to block ports using the "Protocol Sets" policies in Websense, adding the necessary ports in the "Protocols" section. First of all, yes, I know I can use access lists in the PIX to do the same thing, but it is much easier to do it in WebSense. The problem is, that the PIX will only...

Definity G3si with version 9.1 Most calls I get show up with the caller ID. Some, obviously, do not pass Caller ID at all, so I won't get any Caller ID info from them anyway. However, the problem I'm referring to in the subject is that sometimes I wait for the info to show up, even up to 3...

I am doing inter-VLAN routing, etc. from a Cisco 4506 with SUP2 (CatOS) to a 2621XM router. I am performing "router on a stick" (one actual physical interface, many logical sub-interfaces) using dot1q tagging. I have the sub-ints set up on the router correctly. Since I am using DHCP for the...

After upgrading to the 6.3(3) version, I now get what is apparently return packets not being recognized, and thus being blocked by the firewall. It either does not find XLATE or session information, and gets treated as a packet that was initiated from the outside. This apparently does not...

Is there a way to extend the time I am allowed to do a list trace?

Bizarre problem. Not sure what words to use to search, but I searched to see if this was answered before anyhow. One user, an editor of a specific public folder, in fact, can only see her additions or edits of the folder. All other users, including myself (the admin), can see each others...

I have a 1700 series router, a PIX 515e firewall, and a 2621XM, any of which I can use to filter web traffic. A new trick of those trying to bypass restrictive firewalls is to proxy their connection through http or https. These sessions usually stay intact until the person ends the application...

I basically need to block a specific INCOMING number, but blocking the entire area code from calling us is not a problem. I do not have vectoring, and I know ARS is used for OUTGOING, but this call is incoming. I repeat, I do not have vectoring. The call comes in normally over one trunk. Any...

Here's the scenario: I wish to separate traffic between departments (users on their own specific VLAN), then restrict where each VLAN can go (Finance can access their own VLAN, plus the Domain Controller and e-mail servers, and the finance server, BUT NOT, lets say, the RESEARCH server located...

Upgraded PIX image to v6.33 on the 515E here, and now on the syslog, I am getting denied return packets... Normally, I would think I have alot of scans with port 80 for the source port, for example, but all of these have an xlate, and the src coincides with someone on the network accessing that...

Normally, we use one announcement for no answer and busy, and a second announcement for out of hours. For the most part, this works, but in the event of a holiday, or sometimes when it is out of hours AND busy, we will get the announcement used for busy and no answer. How can I make it so that...

I need a station that only allows outgoing local. I am aware of the implications of not having 911 at this phone, as it is just a lobby phone, and if there is an emergency, someone on staff will be able to dial 911 for them. That said, I used an unused COR, set up a different partition group...

I am the administrator of a G3si v9 switch. I would either like to dial in to a DID and receive dial tone, and be able to dial out, using a security code, or since I can change settings on the switch remotely, at least be able to set a specific number to dial out to when dialing in remotely. We...

G3si switch here, version 9. Is there a way to determine on calls in progress who they are connected to? We do have the Caller ID option. Thanks.

I would like to know if there is any option to poll time synchronization data from an NTP server off the Internet for a Definity G3si switch. I believe we are on version 9 of the software, and the switch does have an IP address assigned to it. Also (unrelated), our attendant console somehow...