Search results for query: *

i have an Avaya CM6 software version 6.3. we are unable to activate the MCT feature by dialing the *57 from a phone that has received a call after the call has been hung up. I can assign an MCT-ACT softkey however and it works as the documentation suggests. I can also place a call on hold, grab...

i am trying to trigger a .wav file using aspect on a windows 2007 machine. when i did this on an XP machine i had no problems. I have another script that i am using with the script below to monitor my SL-100 LOGS and play specific sounds for alarm conditions. Below is the script i am using...

i am trying to write a script in Procomm that would monitor my logs for specific output. When the desired log appears on the screen i would like it to trigger an audible sound file on my computer like an alert/warning tone. I have been using the record feature on procomm to try and capture that...

i have read through the forum and i have not found an example of this. I have a DMS100 printer port that i have connected to a PC with a Procomm session running constantly capturing data to a capture file. I want to be able to have Procomm scan for specific alarm codes that scroll across the...

I have a DMS100 conected to M1 with 8 PRI's. Currently for some reason the M1 is setup as Network and my DMS100 is user. When i set them up i make the DMS100 the Network and the PBX the user. My question is does it matter which one is User or Network and would it affect CLID being displayed...

i am fairly new to scripting and i am not sure on how to go about doing what i want to do. Basically i want procomm to execute a command whenever a certain data is output on my terminal session. What would be the best way to do this.

trying to configure the data port for use with a laptop. does anyone have notes on how to do this as well as other setup for this type of phone. i have configured the phones data port with its own SPID, but when i plug in a laptop to the db25 port in back of the phone , and search for the new...

trying to make test calls by grabbing a particular trunk and member. i have my 2616 set up as an MTA and when i log into it and try to make a call i get a TRK017 log. it is telling my that it fails because it is an ISL TIE trunk. is there a diffrent way to do this? i have been using the trunk...

has anyone worked on one of these before? i am in Turkey and have limited resources for questions. just trying to find someone i can bump questions off of every now and then. this system is currently being used to interface traffic coming off of E1 PRI's to T1 PRI's on my DMS100 switch.

i have configured the card and connected it the Taqua switch. Looks like layer 1 is up cause everything greens up . but when i go to LD 96 to check the DCH it is in an RLS AUTO state. everytime i try to establish it , i get an error stating that it is in a wrong state. the Taqua switch is set...

i am trying to get a print out of the clid table and i cant remeber where to do it . i thought it was ld 21 under net_data but i am not seeing what i want. any suggestions?

i have an option 11c with DID's that have 2 diffrent NXX's. one is 323 and the other is 247. whenever i call out of the pbx dialing from a DID that starts with 247 i get an ANI with the 323 nxx instead every time. is there a way to make this send the right ANI every time?

i have an option 11C release 22, is there a security feature that prevents extensions that are remote CFW to go to the attendant if the call comes in without ANI? I ran into this problem when anyone calls into my pbx with a calling card any suggestions?

i have just set up a DTI to my switch and i want to do mf signaling. where do i set this parameter at? LD 14,16 OR 17?

ihave an Option 11c, where can i increase the number of digits that i can pass to my switch? right now i get 10 digits and and i need to get 14 because i am doing authcodes on my dms250.

how do i go about dialing a trunk on my option 11c direclty ?

actually i still want to be able to use 9 to dial out. here is my situation. i have an option 11c and 2 dms250's. i have 3 t1's going to my option 11. 1 PRI to my LEC for locall access; 1 dti to 1 dms250 for long distance; and another PRI to the other 250. right now if i dial long (9+1 +...

i have recently setup this pri up to my dms-250. it seems that the d-channel comes up in the option ll but not my 250. has anyone set one up before, i would like to see if i missed something.

i am programming an 0x32 and sending it to one of my remote sites. how long will settings stay without power to the unit ?

looking for some help, i have a Meridian 1 Option 11C with release 22. My problem is when i have a phone forwarded to an external number and someone calls me using a prepaid calling card it routes to my attendant console automatically. Any idea where i can resolve this in the pbx?