Search results for query: *

just want to check to see if I can remember correctly i need to take the main greeting and add the holiday greeting go to the sdn table, click on the sdn table which is 0 for operator to open the sdn and click done on the application box thats shows all the app name , choose the application i...

hello can you help find this code or tell me what this is thank you

hello how do I find the total amount of liscenses and total amount used

Hello, currently I back up all the user data( Voice and Data)volumes which takes a few minutes I need to do a full back up would I also highlight selective messages & pdls selective Services to make this a full back up????? I hear I may need two tapes for this?

Hello, currently im back up all the user data( Voice and Data)volumes which takes a few minutes I need to do a full back up would I also highlight selective messages & pdls selective Services to make this a full back up????? I hear I may need two tapes for this?

Hello New DID's I have programmed a few to confirm, still acting as a non did is there anything that needs to be change to the PBX to activate these did's. I was advise they should be working. but programmed a few and still not acting as direct numbers...just none direct. Thanks

hello I have 2 numbers key 0 scr xxxx 0 marp = did key 1 scr xxxx D marp = roll over key 3 scr xxxx 0 marp = Did key 4 scr xxxx D marp = Roll over well on the key 3 it rings..but when next line comes in key 4 it goes directly to busy cls is hta...what else should I do thank you

Hello, Im moving 3 consoles tonight...thats all our Attendant console's the cables are being pulled back and relocating about 100 ft... Anything i need to do? other than just plugging them back in. do I need to disable any of the tns or will they just disable on there own over night. Thanks...

Hello The main att console has been ringing and showing this error. 7211 29 0 ld 80 i ran a trac 0 7211 and a list of tn's appeard example all show idle exept 1 29 20 0 0 1 SBSY 28 20 0 0 2 IDLE 27 20 0 0 3 IDLE i have diabled this tn which stopped it going to the att console...

Hello, How do I get a 2006 to ring when the handset has been pick up or knocked off of its receiver. up to go directly to an emergency operation center...DN are all on site. with out pressing any of the keys. Thank you

Hello I have user which message waiting lamp is not working he has a 3905 phone and I2050 (softphone) tn built for him, he just notified me of this change, he has not loaded the software yet. Both tn's have MWA, What can I do to get hs M3905 to light up, he has tried other phones...same...

someone set a password on one of these phones in the option section and has left the company How would I clear this, since its hard coded on the phone and not in the PBX side.

Hello I have experienced getting a cpy of reply (71) and Forward a V-mail (73) and also a cpy of the reply of a forward message (79). I veiwed the class of servic's of my mailbox Retain Copy of sent messages: (No) Yes and it is marked to (N0) Should I be checking some other service's

Were getting a MN on all Console's minor alarms I am clearing the alarm in ld 32 but it keeps reappearing on all consoles.. this has been going on about a week. I though the problem would go away after the system monitor card were replaced.

Hi All A delema again. the console stays on only for about 10 minutes. Every time i plug it back in it works ok..... But then it fades totally out. any suggestions... I think the cable is crimped.

I need to move 2 attendant consoles any suggestions...there stand alone with a 25 pr connected(rs237) Thanks

I have to move 2 consoles soon, there just being unplugged for a day to or so any suggestions. One will be active for at all times... Will the other 2 that will be unplugged affect the function of the others.

Hello 10/27/2004 I have been advise to out and rebuild an ip phone for a acd user on the pbx side I have been told its been de-aquired on the symposium side and outed. but when I print this phone out on the switch , it looks like its just de-aquired and not outed. When I stat this phone it...

Hello I have been advise to out and rebuild an ip phone for a acd user on the pbx side I have been told its been de-aquired on the symposium side and outed. but when I print this phone out on the switch , it looks like its just de-aquired and not outed. When I stat this phone it reads ---idle...

The weirdest thing is happening when im trying to set up an intercom between 2 phones.... its not working 1st phone key 2 dig 7 2 V phone type 3904 working ..... 2nd phone key 14 dig 7 3 V phone type 2616 not working get busy the wierd thing is that it works from another...