Search results for query: *

I realize that the 412 TDL pinouts do indicate a specific polarity, per port. If the polarity is switched on one jack, what indications do you get? I've had a jack to a 44XX phone miswired for a long time and there have been no issues?? Just curious.

HELP! I've had 2 4424LD phones on ports on a 412 TDL card for months and months. I replaced a cord on the cross connect and NOW, if both are plugged into their respective ports, both phones go dead. If I unplug either phone, the other phone comes to life. If I remove both power supplies, both...

I'm hoping that someone out here has seen this problem. I have a Merlin Magix, rel 3 system with Merlin Messaging, Release 4. Everything works well, except my UNIFIED MESSAGING (running the SMTP method, NOT the EXCHANGE method). I have everything set up correctly, both in the merlin...

Don't fall into the same mistake that I did. I very successfully migrated (using my magix 3.0 system) from old Merlin Mail - Release 3, to a new Merlin Messaging Release 4. GREAT NEW FEATURES! BUT, if you use your network, and the Administration software that runs on your PC, to set up your...

Can someone please clarify the following for me.. If there is NO PCMCIA card in a Merlin Messaging, Release 4.0 (or any release for that matter), does this mean that the unit is a 2-port voicemail, or a 0-port voicemail? I've been seeing Release 4.0 Merlin Messaging for sale, with a 2-port...

Hello. I have added a TDL card to my magix 3.0 system. All is fine. I had an MLX-20L on extension 17 on an 412 MLX module, which is working perfectly with my Merlin Messaging release 3.0. I want to replace the MLX-20L, with a 4424 LD, but I want the 4424LD to be extension 17 AND I want...

Is there a minimum release of Merlin Messaging (for MAGIX), that can be upgraded to Release 4.0? For example.. If I have a merlin messaging Release 1.0, 4 ports - Can it be upgraded to release 4.0 with 4 ports. What would be involved? I really want the WEB enabled setup,access and tools. Is...

I am converting from Legend rel 7 to MAGIX rel 3. My current Legend has an 008 ATL in slot 3; FOLLOWED by an 012 Analog port card in slot 4 and an 016 ETR in slot 5. Before I do the magix upgrade, I need to permanently remove the 008 ATL in slot 4 (I only have two phones on this card). Does...

I have a 4 port Merlin Mail Release 3 (the type that hangs on the wall). It has worked beautifully for three years. It has now started calling the operator position from ports 1 and 2; and leaving a message that just has a ringback in it. I disconnected ALL FOUR of the connections to the port...

I have a legend R7 w/ a 4 port Merlin Mail R3 (the one that hangs on the wall). All is well with the voicemail, including the auto attendant answering the phone; HOWEVER, when a fax call comes in, the auto attendant transfers the call to the fax extension (44),as expected. The fax machine...

Does anyone have a Merlin PFC? I need operation information or a manual. I connect it to the switch (Legend R7, With ATL ports), and the phone works great, fax RECEIVE works great too. I can't figure out how to SEND a fax! Any information is greatly appreciated. Thank you!

I would like to know if I can safely remove the PCMCIA translation card from my Legend R7, Version 10 processor while the system is running. I want to store it in a safe off-site location, I intend to place ANOTHER translation card back into the processor and do a back up on it; and let it...

I have a Merlin Legend R7, V10 System that is running very nicely. It has the following configuration: Slot 0 CKE4 Processor Version 7, Release 10 Slot 1 408 GS/LS ID (caller ID version - w/ 8 MLX ports) Slot 2 408 GS/LS - MLX (music on hold is on port 4) Slot 3 008 (supports older Merlin...

I have a RAM failure on my Merlin Legend CKE4 R7 V9, so I purchased a refurbished CKE4 R7 V10. (I assumed that CKE4 Release 7, any version 9 or greater would be OK) I powered down the system, removed the original processor (V9) and installed the new (V10) processor and put my translation memory...

I have a merlin legend R7.0 V9.0 that now has an alarm light on the processor (CKE4 processor module). The error code is 780E. This is described as LOWER ROM FAILURE; Memory failed ROM test; turns on processor LED. If problem persists, replace processor. Although the error light is on, my...

Is it possible to get incoming caller id information (from an outside line) on the display of the Transtalk 9031 and/or the Business Cordless 905. I currently have them connected to ATL ports. I know that caller ID is not supported in this configuration. If I purchase and ETR module and connect...