Search results for query: *

While I was reading through some documentation I found this : " When a router is routing IP, an IP broadcast will never be forwarded from one interface to another by default. An IP broadcast can be forwarded between interfaces if the router is transparently bridging, but will not be forwarded...

I am looking for some good resources show me how to setup be VPN session between a dailup Desktop (XP) at home and Laptop (Win2003) connected to ADSL router (WAG54G V2)at home as well (i.e I have two type of connections Dialup and ADSL). I am looking for resources for all these requirements...

I have got two computers at home, my laptop (win2003) connected to ADSL linksys WAG354G (wireless not wired) , and I have got a Desktop PC connected to noraml Dialup modem, I tried to establish VPN between them , by using microsoft client utility on the Desktop PC, but I faild to open the VPN...

http://img89.imageshack.us/img89/4172/framerelaydlci7nl.jpg What is placed in the address field of a frame that will travel from the DC to Orlando office? Is it DLCI 200 (which I beleive) or DLCI 200 and DLCI (100)?

I have got windows 2000 advanced server , I created a user and when I tried to click on "member Of" tab, I received this error message: See the link please: http://tinypic.com/fozwgy.jpg I found this link, but I did not play with it , because it is dealing with registry...

I just want to know in general, does a telecommunications switch can handle different layer 2 wan technologies (Frame Relay, ATM, ISDN--etc)? or it should be specified for specific technology only ? Yes I know there are different modules and type of switches, but I am looking to know does it...

With Hub and spoke topology, If R2 is hub and R1, R3 are spokes,,,,and if the question ask : 1- Configure OSPF area 0 on the Frame Relay connection between R1, R2, and R3. 2- Do not use the "ip ospf network" interface command on R2. The task above states that the "ip ospf network" command...

Internetwork Expert Lab for CCIE says: "Another two configurable network types that are left are therefore point-to-multipoint and point-to-multipoint non-broadcast. Point-to-multipoint non-broadcast is used in NBMA environments with virtual circuits of differing speeds". Cisco says...

I have got LinkSys Router WAG354G (not WAG54G) at home , I have got the mail server with static ip address 192.168.1.64, and the web server with static ip address 192.168.1.100 If I want to access these services from the internet, I have to configure port forwarding, but with my Linksys I have...

Dear All I tried to follow the instruction in this link: http://multiboot.solaris-x86.org/v/2.html I created all these partitions as mentioned in the link above by using partition commander 9 Fist stage: I installed XP in first partition (hda1)....success. Second stage: Install...

Hi All Regarding to this article: http://support.microsoft.com/kb/816514 The article mentioned: Build a Filter List from NetA to NetB 1. In the new policy properties, click to clear the Use Add Wizard check box, and then click Add to create a new rule. 2. Click the IP Filter List tab, and...

I divided my 40 GB HD as followed: 3GB primary (Win XP), 4GB also primary unformatted to be for Solaris later on, 32GB primary Extended .I had done partitions by using software Magic Partition I succeeded to install Win XP and Linux, the boot Loader is LiLo. First I installed Win XP, and...

Hi Every one I have got problem when I try to ping my self..I received this message : "Request timed out". my operating system is windows 2000 server. The ip address that I used was 193.16.16.3 and I tried other. I have got no problem with loopback (127.0.0.1). only my problm is...