Search results for query: *

Hey there - I was searching through the forum - but could not find anything surrounding this. I want to call from my home phone into our company PBX - then make an LD call outbound...

I tried using LD 23 to create a DN and to have it NCFW to an 800 number with has a local DN tied to it. Having said that - these numbers go into a phone queue and don't terminate on a particular phone set. - When I try to dial the ACD number it's goes straight to voicemail. When I NCFW the ACD...

Is it possible to have two phones run off of one TN? I don't think so...but I am not entirely sure

How do I setup an announcement to play once a number is dialed. This is what I have tried - I setup and ACDN via LD 23 and setup my NCFW to my meridian mail and setup a mailbox to play the announcement - but how do I not play the meridian mail blurb and just play the announcement instead without...

I have an option 11 with Meridian Mail built it - I would like to know how many TN's I have currently mapped to my merdian mail DN. How many lines does my PBX have to my meridian mail.

Hello - Can anyone tell me how to list what trunks I have -Specifically trunks to the PSTN? Also I would like to find out DN's I can use from my PBX. I have used ld 20 >> LUDN -but I want to list all DN's instead.

How can I tell what speed and duplex settings are on my ITG card. Can this be done by dialing into the switch - any specific LD command? Much Thanks,

What ld command would tell me what modal Meridian PBX I have? Much Thanks!!

ld 32 NPR000 .stat 000 = SUPER LOOP 000 DSBL 001 BUSY 004 = SUPER LOOP 000 DSBL 002 BUSY 008 = SUPER LOOP 000 DSBL 000 BUSY 012 = SUPER LOOP DSBL NOT RESPONDING 016 = SUPER LOOP DSBL NOT RESPONDING 001 = PRI TRK LOOP 00 DSBL 01 BUSY NPR301 029 = CNFC LOOP...

Hello - Can someone tell me which load command would tell me how many trunk ports I have, and additionally if I have a PRI connected how many timeslots are configured - Much Thanks - and have a great weekend!!!

I have a user who sits at site 1 ext 2401 and who also sits at site one ext. 4660. I would that when anyone calls his 2401 and if does not pickup - to have it forwarded to ext 4660 and if still nobody picks up to then get sent to v/m. This is the setup of his phone at site 1. Thanks for your...

I have a user who sits at two desks at two different sites (seperate PBX's). Site 1 DN 7700 has mailbox Site 2 DN 4408 no mailbox When she is at site 1 she forwards all her calls from 4408 to 7700 and when at site 2 forwards all her calls from 7700 to 4408. However, when she has leaves for the...

I have a users who just recently started complaining that when she picks up calls on 7229 - that anyone else who calls that number while she's on the phone gets a busy signal. The programming looks fine - I don't know what else to look for?? Much Thanks!! TN 013 0 00 11 DATE PAGE DES...

I have a DN that I don't want to assign to a TN but would like all calls to that DN be automatically forwarded to the MCDN - Not sure if this is important - but the DN is mapped to an 800 at our local telco. Thanks again for everyones help!!

Is there a simple way to determine if an MCDN number has an appearance on any TN's?

I have been doing some reading here and it seems the only way to forward a DN on a set is if it is MARP'd on the set. I have done this however I cannot forward an extension to V/M without it ringing 3 times. I want to get 7229 to goto V/M however only 7224 and 8224 go when call forward is...