Search results for query: *

I have a 2960 switch and a router and I'm planning to create two VLANs with private IP subnets in the catalyst. I will connect this catalyst to a router with public IP addresses. My question is, how will the hosts connected in the catalyst browse the internet? a sample configuration or a brief...

Hi, I'd like to know how far I can extend a physical connection between two routers using both WIC T1 DSU interface card. Thanks..

Hi, We have an Option11 with 600TNs, However, when 150 TNs are simultaneously calling, other DNs are experiencing no dialtone. Is the 600TNs synonymous to 600 simultaneous calls per system? How do we check the number of simultansous calls allowed per system? Thanks, Pedro Penduko

One of our application needs a trunk to trunk transfer capability where an analog line will access a DTI trunk and once connected the call will be transferred to another DTI trunk. Is this possible? Thanks in advance! Penduko

Hi, Is there a freeware or shareware software that will enable a user to see the 'translated' CDR for incoming and outgoing calls on a realtime basis? Regards, Penduko

Hi, What are the things that I have to do to display the CLID to digital phone's LCD (display) from an ISDN trunks. Right now, the displayted information is the ROUTE ACOD + MEMBER NUMBER.... Thanks in advance... Regards, Pedro

Hi, I'm having problems passing calls between Option11 and other equipment via ISDN PRI link. Layers 1 to 3 are up on both equipment and it is when I'm passing calls between the two when problems begin to arise. Below are the results of debug after I enable the MSGI/O on the configured DCH in...

Hi, We are currently running a CTI application and its server is connected to our Meridian Option 11. The problem is during peak hours of calls, there are instances where the system and the DNs are experiencing no dial tone problems. Do you think that adding NTAK03 on the sytem will resolve...

Hi, I believe NTAK09 can do ISDN PRI, my questions are: 1. What type of cable is needed to connect this T1 to a remote ISDN PRI? 2. Is a clock daugtherboard needed? Thanks........

Hi, I'd like to know if it is possible to convert an incoming FGD call from 10/11 digit down to 4 digit internal DN and be routed to a particular DN Please see scenario below: 1. A foreign trunk (FGD) dials 12013465555 going to my PBX 2. Digit Manipulation takes place allowing the call to get...

Hi, Our Option11 has FGD feature and we want to implement it to our new telco interconnection (requiring us to use FGD). Relative to this, can anybody redirect me to a simple implementation and configuration of FGD via Nortel Meridian Option11? Thanks, Penduko

We have purchased an old SAGE 930A communications test set with no cables..... I have two free bantam jacks but I don't know how the pinout for bantam to phone jack connectors.... please help, thanks

Here is the setup LAN A(1751)-[mdmA]-512KbLocLoop(Radio 250mi)-[mdmB]-(1751)-LAN B Modem A is a 4 wire Baseband Modem (full duplex) Modem B is a 2 wire Baseband Modem (half duplex) 24 hour BER test subs to subs had couple of BIT errors The two LANs can see each other well but their are...

Hi, What are the things that I need to consider and overlays that I have to read on? Thanks

Is it okay if I use Cisco 1751 with WIC 2T for an E1 connection coming from ISP? The 1751 will be used for routing IP packets only..... thanks

Hi, I have encountered this problem in my E1 p-t-p (2611 ptp 2505) routers. Below are their configuration: Router A (2611) =============== interface Ethernet0/0 ip address 192.168.2.1 255.255.255.0 full-duplex ! interface Serial0/0 bandwidth 2048 ip address 10.10.83.3 255.255.255.0 no...

Hi, We have purchased two Fiber receiver recently with their corresponding cabinets for opt11. I just want to ask the basic tasks we need to do to configure the two cards? <Cab1><CPU ><-----fiber-------><ntdk23aa><Cab2> | ---------fiber-------><ntdk23aa><Cab3> Thanks in...

I'am currently looking at the scenario below: LocA<1750>--<AdtranTSU>--LocLoop--<AdtranTSU>--<1750>LocB Cisco 1750s connection to adtran is via serial (s0) to V.35 Each Cisco has WIC 2T card connected to their s0. Adtran's free timeslots are 21 to 24 making the connection 256Kb (the link...

What is the fastest way to transfer the complete program of one opt11 to another opt11? Thanks.....

Location A LocationB loc DN(opt11)<-Mux->LocalLoop256Kb<-Mux->T1(otherSW)loc DN A caller in Location B wants to call a localDN in location A using the diagram above. Settings for T1s on both location AMI/D4 E&M Immediate Start T1s for both location are in sync. Calls...