Search results for query: *

Has anyone configured a 3550 to act as a DHCP server to connected workstations. If so, please provide any information you have. Thanks

I cannot get any power to my avaya phones from the the switch. I've "set port inline power x/x auto" still no power. slot 9 - WS-X6148-RRJ45V system ver: 7.1 system file: cat6000-sup2k8.8-2-2.bin Do you guys have any suggestions? Currently, I only have 2 phones connected.

Has anyone configured a tunnel between the PIX and Contivity 1700. If so, please provide any notes or configuration examples from your setup. Regards,

I have a network of about 29 switches that are grouped 3-4 switches per vlan. Each switch currently has an IP address and can be accessed remotely.... these are all 2950s. How would I go about taking advantage of CMS in this scenario? Thanks myng

What commands should I use to find who(which mac) and most active talkers on a switch? I would like to be able to identify the port/s with the most activity. Thanks for any assistance myng

Here is my dilemma, I have a server behind a PIX that needs to function as a web server and also respond to webmail that will be coming in on port 80 also. How do I accomplish this task via the PIX. Thanks for any help!!!

I'm trying to setup NAT with subinterfaces Cisco 2691 Router-Fast0/0 ==> WAN -int f0/1.1 ip 192.168.20.1/24 -int f0/1.2 ip 192.168.30.1/24 -int f0/1.3 ip 192.168.40.1/24 Here's the ??? to accomplish this shoud I: 1. int f0/1.1 ip nat source list 1 access-list 1 permit 192.168.20.0...

Please help, I need to setup a 2691 to function as a DHCP server for 3 seperate departments. The goal is to keep the departments' traffic separated while allowing the 2691 to issue DHCP addresses to each department. How should I approach this? *multiple inferfaces? *or will vlans and...

I'm trying to deploy a network using the pix 515e with FOS ver 6.3 Has anyone tried configuring VLANs between the PIX and Cisco Catalyst 2950's. The following link from Cisco explains what i'm trying to accomplish...

I'm trying to deploy a network using the pix 515e with FOS ver 6.3 Has anyone tried configuring VLAN between the PIX and Cisco Catalyst 2950's. The following link from Cisco explains what i'm trying to accomplish...

The following is a diagram of a network that I would like to isolate traffic from each port most efficiently. Thanks for any help!! {pix 506e} | | | {cisco 2950-48} | | | {cisco...

Does anyone know if multiple DHCP pools are supported by the PIX. dhcpd address 192.168.1.x-192.168.1.x inside dhcpd address 192.168.2.x-192.168.2.x (??interface??) Thanks for your input!!

any recommendation for an IOS to test MPLS in my lab? I have several 2500 series routers.... thanks for your help

Please provide advice on the following: PIX connected to ISP on outside interface, providing dhcp and nat for the entire network. 6-switches connected to the inside interface of the pix. The switches will have 192.168.x.x addresses on the mgmt. interface. A public IP will be on the outside...

I'm trying to connect 2 routers in my lab back-to-back through the AUX ports. The interfaces will not come up, PLEASE HELP!! Here are the partail configs FR-SW>sh int async 1 Async1 is down, line protocol is down Hardware is Async Serial Internet address is 192.168.10.1/24 MTU 1500...

HELP!!!! whenever I reboot my router the config is lost everytime. I'm absolutely sure to "copy run start" or "wr" however, I have to reload the config after every reboot. Could the read only flash be causing this problem? I am able to erase the flash, but when I reboot...

I purchased a used router cisco 2503, I went through the password recovery successfully, however, when I attempt: copy tftp flash I get the following error: %Destination file system is read-only. Also, I recently added an additional 8mb flash, could this be the problem? Please help me...

I'm a newbie to router configuration: I have (2) cisco 2503's with an ethernet transceiver for both AUI ports. I would like to connect one of the routers to a cable modem and be able to access the internet via the second router. Current ios: Cisco Internetwork Operating System Software IOS...