Search results for query: *

Hi The situation is that we have three 4510R Switches with, among other blades, WS-X4418 18 Port Server Switching cards. I know that on the 4418 ports 1 and 2 are the only non-blocking ports and that the others are not fabric enabled. I need to know if it is possible to create an etherchannel...

Hi I need to set up a vpn using Cisco PIX. The requirement is to tunnel in via a client to the internal network and once within, tunnel to a second site via a site to site vpn. Confusing I know, but is it possible and are there any pitfalls I need to be aware of? Thanks in advance.

Hi Has anyone done this? I want to use an ipaq to connect to routers in order to configure SDM. At present I can get to the login screen but cannot get to SDM. I suspect it is a java issue but need some pointers.

Hi They all come along together Has anyone tried forwarding a range of ports with 1 command? I am thinking along the lines of: static (inside, outside) tcp 192.168.0.1 1024 - 64000 192.168.0.100 1024 - 64000 Possible, madness, yes or no?I do not have the machine here to test this command...

Hi Has anyone seen the following IPSEC(ipsec_encap): crypto map check deny Is it an error? I have a vpn tunnel that will not come up and need to now if this is the problem.

Hello Has anybody networked Cisco Call Manager Express to an Avaya S8300? If so do you know where I can find some documentation/tips/hints etc? I am close to getting it working but not quite there. Any help/advice/suggestions more than welcome (including whether this is the right forum

HI Basically, is it possible to do what the title says? I have a 2621XM with CCME and SDM onboard. I cannot now get to the CCME GUI since installing SDM. I have tried typing http://xxx.xxx.xxx.xxx/ccme.html as instructed in the documentation but this returns an error (page cannot be...

HI Basically, is it possible to do what the title says? I have a 2621XM with CCME and SDM onboard. I cannot now get to the CCME GUI since installing SDM. I have tried typing http://xxx.xxx.xxx.xxx/ccme.html as instructed in the documentation but this returns an error (page cannot be...

Hi I am connecting to a 2621XM router over dial-up, using the Cisco vpn client. I can connect and I can ping the internal router interface, but I can't do anything else on the local LAN. I cannot http into the router and cannot get to an ftp server internally. This is a simple setup as its...

Hi I have set up a single remote access VPN into our test network using easy VPN terminating on a 2621xm. I can connect to the network but cannot see anything internally. The IP address I get is within the internal range and we have dhcp excluded addresses on some kit, but I can't ping them...

Hi I have been given a Catalyst 5500. It has just a single supervisor 3G. I cannot console into the supervisor but all the LED's are green and it appears to be OK. Any ideas at all welcome. It seems a shame to dump a 13 blade chassis.

Hi I have two Aironet 1200 AP's. I only want to prove to myself that they support WEP. I can set up the AP. I can browse to the web setup page. I can get to the internet through the AP. In short, it works. The trouble starts when you attempt to configure security. If I configure the AP for 40...

Hi I have installed PDM and used it on all PIX except the 506e. I installed it today on a 506e. I have the Java settings correct on the PC, I have the correct browser, the addresses are all set and the versions of PDM and the PIX IOS are 301 and 6.3 respectively. I have no personal firewall...

Hi I have a 2620 with the module named above installed, as well as a WIC-1BS/T. Has anybody got the bare bones config for the E1 module? I have a config, but it looks all wrong to me, compared to samples I have seen before. The E1 is currently showing a local alarm and passing no data. It is...

Hi I need a router or switch to take in traffic then route that traffic out of one of four Ethernet ports dependent on the SOURCE IP address. I have been advised that Policy Based routing will do this, but nobody at Cisco seems to know what platforms they make that support it. Specifically...

Hi Does anyone know what modules on the 2600XM range support PBR? I don't need to know which IOS or which model, but which WIC or NM. Cheers

Hi I have not used Watchguard before and so 6this must seem pretty basic, but it is driving me mad. I have a Watchguard V10 straight out the box. I have cabled the Private Interface to my laptop via a crossover cable (i've tried with straight through via a hub too. I have the V10 started up. I...

Hi Has anyone ever configured point to point links over G703 from a Cisco router? I don't know the full ins and outs of the scenario, but the user wants to connect three small offices together for data only. They want to use G703 between the sites and I have to confess its something I have...

Hi I have a 1760 with 2 serial lines going to different destinations. I want s0 to fail over to s1 in the event of s0 going down. No problem. I also want the traffic to fail back over to s0 from s1 if s0 becomes available. Would I be correct in assuming that 2 static routes, but a more...

Hi I have a new PC into which I installed 2 Network Cards. One is an Intel 10/100 Ethernet, the other is a Belkin Wireless Ethernet NIC. I am running windows 2000 pro, the Intel card is fine and it can see the Belkin card, but reports it (Belkin) as having a problem. Can anybody walk me...