Search results for query: *

Hi, everybody, This is the setup: Cisco 1720 IOS 12.1 Area0 serial0 encapsulation PPP IP 192.168.60.2/24 serial1 encapsulation PPP IP 192.168.62.1/24 Area2 fastethernet IP 192.168.31.1/24 1. I don't have loopback interfaces configured (I know they are elected as router ID. 2. All OSPF...

Hi There! We have a DID route to a Nortel DMS100 using MFC R2. We want to improve the link by upgradng signalling to EuroISDN PRI. Do you know if DMS100 can handle that (without SS7)? What parameters should we consider when doing this? (We have a lot of PRIs to Ericcson AXE, Siemens EWSD and...

Hi, everybody! The good news: We are growing! The bad news: Ran out of space in premises or nearby Apart from remote and convergent solutions, we think in a second call center networked... Because of lacking of vendor support (my all-time complaint), The question is: What should I buy (and...

We have experienced inits after several loops fail or when a loop is restored repeatedly. It happens in Succession 3.0 and 25.40 (and happened in Rls 22, 23 and 24.30). Both PBX are 81C FNF. I have to mention that our loops are E1s. It is really annoying because we have over 45 E1s (some of them...

Hi there! We have frecuent problems with MLSM, which gets down and sometimes it also affects TFE (those times we need to startup or reboot SCCS). The message is: 41505 Major System Manager Service Service MLSM_Service terminated unexpectedly, rc=243 The problem is more frecuent in high...

Hi There! Due to resizing, We had to reinstall a SCCS Backup. Partitions in Active SCCS are 4x8GB, and partitions in Backup SCCS are 4x16GB. Our provider says we cannot restore a database from active server in this backup server so we are to lose all historic data, and type all configurations...

Hi there! I had a power outage a couple of weeks ago and I had an eye on the 4 rectifiers (MPR25)... They went over 28Amps each one and the power outage lasted only 12 minutes. The battery backup is designed for 2 hours. The 8 Batteries (2 banks of 12V-75AH ea.) are OK as they were tested the...

Hi There! (different site than the other post) We have 81C CPPII in Rls 25.40 and we have OTM 2.0. We experience some problems in SML (some services going down) when OTM captures traffic reports from meridian and we experience real high traffic. What can be done to solve this issue?. elan...

Hi there! We needed to upgrade one of our 81C from CP4 to CPPII, for capacity reasons, and Nortel forced us to migrate from Rls 25.40 to Succession 3.0. As a result they said we needed to change Meridian MAX SNN8.71 for SCCS We are using Genesys 6.5 (migrating to 7 soon) for part of our call...

Hi there! To get a clear idea of what we want I´ll picture the schema: We have a dialer (Genesys OCS v6.5) using Dialogic E1 Card connected to a lineside in Meridian Op 81C FNF R. 25.40 We are getting busy codes in CPD for rejected calls, that means failure on phone lines or No path found...

Hi, there! First of all, This is the platform: We are working with Genesys 6.5 and Symposium Meridian Link 4.2. Our PBX is Meridian 81C with 25.30 (going to 25.40B in few days). One thing worries us: The long time it takes to recover the operation with Genesys if we work in Meridian and we...

Hi, everybody, I have a 150 member route (MFCR2) to a company, and sometimes they see many of their channels in "seal" state (Ericsson AXE) because it doesn't get Seizure acknowledges. Meanwhile we didn't see any different from IDLE or BUSY. Tracing down the problem we could reproduce...

Hello! We have a Meridian Max 8.71 (SNN Platform) and we want to change the hard disk,which is of 1GB currently. There have been some read/write warnings and also it's pretty small for our application. Our vendor says it´s only possible to change the disk for one of the same capacity without...