Search results for query: *

Here it is: CICS6.1 CP150; When business closes and uses time table greetings and ccr plays correctly. Now bad weather is coming and customer wants to close for day tomorrow... F 982 business closed OK, but only closed greeting plays not the tree that normally follows the night greeting. Whats...

I have a new customer that had nite ring thru the over head page when in nite service. Something happened "event" unclear but they (cust)replaced pwr supply and paging came back but not nite ring(Older 8x24DS W/DR5 with startalk mini, Valcom 24v speakers and pwr supply) the paging works fine but...

CP150 on ICS 6.0 this setup has been in service for about 2 months and about 2 weeks ago it started answering incoming calls with this message "cannot continue with this session, goodbye" and then disconnects. If I or the customer reset the CP by powering down for about 30 sec. When it comes...

CP150 on ICS 6.0 this setup has been in service for about 2 months and about 2 weeks ago it started answering incoming calls with this message "cannot continue with this session, goodbye" and then disconnects. If I or the customer reset the CP by powering down for about 30 sec. When it comes...

Customer wants many phones to ring at the same time on incoming calls after it rings say...4 times at ext. 201. I'm looking for some sort of delayed ringing, but all I see is "appear and ring" or programing for "answer DN" or "foward no answer" I must be brain dead...

Customer has ACS 5.0, in 5 slot carrier as follows, 206e,400, ACS proc, partner mail vs R4 remaining slot empty. set to answer night only, but answers after 5-6 rings saying "Your call is being transfered" and rings at ext 10. Hunt schedule#507 is night only. The question is can I make...

I'M HOOKING UP AN ANSWERING MACHINE TO AN ATA ON A CUSTOMERS CICS WHILE HIS FLASH IS IN FOR REPAIR. I THOUGHT IT WOULD WORK REALLY GOOD. BUT IF WHEN I DIAL THE ATA EXT. THE MACHINE ANSWERS BUT THE PHONE DOESN'T SEEM TO DELIVER A LONG ENOUGH TONES TO ACCESS (TRIP THE MACHINE) TO GET MESSAGES, IS...

I'm trying to get the ext. #'s for the Partner VM. 5 Slot carrier slot configurattion is as follows. 1)400E 2)206E 3)ACS proc. 4)4 port vm I would appreciate any help. Thanks Scott in KC Phonman@comcast.net SMalcolm CustomPrewire in K.C.

My customers attendant phone (221)does not ring when a 2nd call comes in when she is on the phone with a previous call.... it just goes straight to her voice mail. I've checked "foward no answer" and it's set to 6 rings, "foward on busy" is at none. what am I missing? Thanks...

DOES ANYBODY KNOW WHAT THE RING VOLTAGE (AC & DC)IS ON A 206 STATION PORT ON A PARTNER II. I HAVE A CUSTOMER WITH A OFF PREMISIS EXT. LOCAL TELCO SUPPLIES A TIE LINE BETWEEN THE TWO SITES. I'VE GOT ABOUT 56 AC AND 75 DC @ RING. TELCO SAYS I SHOULD BE SUPPLING 85 TO 96 AC VOLTS OUT OF MY STATION...

I installed a couple of door phones on a ox32 after which a "answer door" button was asigned where I had a external page button. The customer would like the page button at it's previous location. I am unable to F*3 a page button over the "answerdoor" button, and can't find a...

0x32mics5.0, nam4.0, Question is: 102 is the general delivery mail box, receptionist also wants personal mb (mb221) can I make ext221 the ext for both mailboxes so that she will have message notification when a message is left in either mb. or am I asking for trouble and confusion when her ext...

I aquired a flash2 w/ACD software. how does it work? or more to the point, does it have mail boxes? or does it just direct the call to an ext. Can I have it answer the line just after hours? where can I find programing instructions? If anyone has any info/insight on this I could use the help...

OK- I've got a DID line that my customer's old phone #'s are directed to. what he wants is a mail box/ info box that doesn't take messages. This box will give customers the new address, location info, not take messages, but still allow the caller to zereo out to get to the auto attend. or the...