Hi guys
I am a bit of a VoiP newbie so sorry if this sounds like a silly question. But the UC520 doesn't support SRST, so how do users make calls if the WAN link fails? Hopefully this is an easy answer!
Thanks
----
Sunyasee
Hi
I am quite new to HP switches, but I have worked with Cisco in the past. I just wondered if it is possible to setup a Qos/CoS policy to garantee a % of bandwidth for certain applications using HP switches.
We have a scenario where a customer has a point-to-point 100 Mbps link between two...
Hi
I have a network with two ISP connections. I want to use both links so that effectively I have a default route over both connections, I have an ASA and obviously it is not possible just to add in two default routes. Routerman suggested in an earlier thread that you can do this by setting...
Hi
I am unable to get passive FTP to work through an ASA. Has anyone come accross this problem before and has a possible solution?
Thanks
----
Sunyasee
Hi
Bit of a strange question.
I have an ASA that has connections to two different ISPs. There are about 10 remote sites that connect into it over VPN. What I want to do is connect one interface to ISP 1 and another to ISP 2. The idea is that some remote sites use ISP 1 interface address on...
Hi Can someone tell me the command to TFTP a config back onto a PIX. I have made a backup using the command 'write network' but am unable to work out the command to put the config back onto a PIX?
Thanks for any help.
----
Sunyasee
Has anyone ever configured a Pix to Pix VPN with overlapping networks? Is this possible? I have found examples of Pix to VPN Concentrator, but have not seen an example of Pix to Pix. I need the whole networks at each side to talk to each other.
Any help would be gladly appreciated!
Thanks...
Hi,
I am trying to configure SDSL with BT and am having lots of problems!! They say that the line is fine and it must be a problem with the config on my Cisco router. Does anyone have a sample BT SDSL config that works that I can compare mine with?
Thanks
----
Sunyasee
Hi
Is there such a command on the PIX to enable split-tunneling for a PPTP client connection.
I need the PPTP connection to have split tunneling. I know the command 'vpngroup XXX split-tunnel XXX'does this for IPSEC VPN clients.
Thanks
----
Sunyasee
Hello
I am trying to work out a solution to enable load balancing with a PIX that is connected to two routers that each have a 2mb connection to the same ISP. The idea is that the two routers are configured to load balance and give 4mb of bandwidth. Trouble is how do I configure the PIX to...
Hi,
Hope someone out there can help!
I am trying to install this camera on Win2000, I have downloaded the drivers and installed them, restarted my machine and then connected the camera. It trys to install but I get a message saying...
'Completing the Found New Hardware Wizard
Sony DSC
An...
Hi,
I am trying to setup a VPN configuration from a Pix 515 to another VPN device. I receive the following error message..
crypto_isakmp_process_block:src:1xx.xxx.xxx.123, dest:2xx.xxx.xxx.125 spt:500 dpt:500
ISAKMP: phase 2 packet is a duplicate of a previous packet
ISAKMP: resending last...
Hello!
I am setting up a PIX with an internal network of 10.0.0.x with a DMZ network of 192.168.1.x. What I need to do is allow communications between a server in the DMZ and a server on the inside network, communication needs to work in both directions and needs to be restricted to just one...
Hi,
I am trying to set up a VPN between a PIX to a 3com Firewall. The PIX Firewall is performing NAT so the network is numbered with a private IP address range. At the other end of the VPN link they have just public addresses and no nat is taking place. I was wondering how to setup the...
Hi,
I have a question, I used to use VPN client 3.6.3 to connect and then telnet to the outside interface of a PIX. But I have recently downloaded a newer version of client and am now unable to telnet to the outside interface once I have a VPN connection. Does anyone else have this problem...
Hi Guys!
I have a question about using the VPN client to connect to a remote PIX from behind my own PIX which is running NAT/PAT, previously I have only mananged to get this to work when using static translations for devices that need to use clients. Is there another way without using static...
Is there anyway of increasing the idle timeout on a VPN tunnel between two pix firewalls. The lifetime is set to 86400....
isakmp policy 10 lifetime 86400
But the VPN tunnel is only staying up for 20 minutes and then the tunnel drops. Any ideas?
Thanks ----
Sunyasee
Hi
I've just installed a Pix Firewall on a network that was running proxy server on Small Business Server and have (tried) to remove the proxy settings from the server and clients. Clients can ping out ok, can get their mail, but are unable to browse the net. I can get out fine from my...
Hello,
All users are getting the strange error below when attempting to connect to the server. I've tried reseting the passwords, creating a new user account and even tried connecting from outlook running on the server itself but still can't log on to the server. This is the error message...
Hi,
Does anyone know of a way to prevent the VPN client connection from timing out after about 20 minutes? I need to keep the connection open for long periods of time, but whether the connection is idle or not it seems to timeout after about 20 minutes and disconnect. I've tried adjusting the...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.