Search results for query: *

what Common control and other Card beside IP-PAD to Install and use DT 700 ip Phones on SV8500 Any Manuals that give more infromation! Fusion Network! Just the cards and types would really help! I know you need License also! Thanks for any help!

Dterm Desk Phone Series I 16 Button showing R.I.P. Not the Time Date and Year Any one every had this problem? Thanks , Bill

Hello , Techs Nec Dterm Desk Phone Series I Display shows R.I.P. not time when Idle believe Some one left Message when 2 Extensions Busy programmed Message Button not sure is there a way to find the Extension that did this. Or how can you cancel it! Tried to Cancel but also look in Features...

Hello , All Tek When SV8500 Maintenance Diagnostics at 2:00 am lost main clock failures abound TSW Card failure Switch over failures PLO Alarms then rebound Clock Re-SInk and system Recovered from looking at Alarms.But all of sudden started have a few tickets come in with Dterm phones Prime...

How to enable call history log on SV8500 DT300 Phones Feature not Available = N I think was thinking and it is what shows under C-195 Manual SV8500 Manual SV8500 dpm- Business please let me know if everyone agrees with this! I think these phones only for sv811/sv8300 Systems?

Seen this post can anyone add to my question on this post Thanks , Bill Is Pa 16 ELCN- C same as PA 16 elcn - A-B Circuit Card I need more ports that will support DT 300 12 Button phone

I have been working on SV8500 that many hands been in. But seen error come up SMDR size Buffer Error Index 249 and 250 Program same 00 Both set same any help on this has not happen but once!

Hello Techs SV8500 Set SFC for Analog Phone sets Caller ID still not working will this work only with Nec Analog Sets and not other Company Display sets check asyd and asydl any one tried this or get it working Panasonic Single line phone display says it will work if Provider sending...

Need little help with Finding Manual for TSW pl0 pl0-a only have CLK 0 and it is on Pair 8 L11 Cable possible upgraded from Neax 2400 ims/ipx to SV8500 But cables flip over to CPU002 Any Links or possible CLK1 pair 7 or 15 MOH R1 TIP 2 Split. Can't find Peripheral Equipment Manual for 2400...

thread937-1702849 trouble adding 8 port analog card blade only has CCIs link 01.16.01 tried adding analog port card in slot 01.18.01 and 01.15.01 but in setup set card type LC8 apply then read reset to blank again.any ideas

Does anyone know SV8500 Command that will show CPU Type CPU 00 or CPU 02 Or should you just get serial numbers on front? Thanks for any help!

SV8500 Asyd SSystem 1 Index 65 seem shows Data FF Lsyd Sys1 Index 65 = Data = FF(11111111) FDATA = 00 AND MDATA =00 Could this be causing a limit on how many Trunk Routes we can Have! Please share what you may think on this! All has been tested but think possible some one has disabled Receive...

Sv8500 pri channels idle but network provider say they can't see layer1,using as Tie line to Cisco VOIP routes and for operator trunk routes setup months ago By other vendors any suggestion to what commands to check.Vendor can cause link to be lost test ok,no errors in Dtfd, Thanks Bill

SV8500 need to change out Attendant Console to VOIP Stations see Calling party Number Conversion but but think hardwire inside cabinet rt901 need to be able to forward operator calls but didn't work with ACFS Any suggestions would be great. Just changing to over to VOIP Desk phone for Auto...

Hello , All Working on a site that they want to add and change Hot Lines from 4 digits to 3 plus Star, But found already a 199* =199 Star which goes direct to Acd Route 60 and intermittently plays Announcements 1 = 12 . Can't find 199* in Dial Plan or in access codes also no Code for Play...

Hello , All Working on a site that they want to add and change Hot Lines from 4 digits to 3 plus Star, But found already a 199* =199 Star which goes direct to Acd Route 60 and intermittently plays Announcements 1 = 12 . Can't find 199* in Dial Plan or in access codes also no Code for Play...

Hello, IT Professionals I just join a group of users to help them on NEC Neax 2400IMS SV8500 they currently have some CISCO Desk Sets working but don't have SIP Server or Trunking? but ask me to help adding some Station looked at some programming see Blocks of DTERMI Phones in Listup.What...