Search results for query: *

I am having a very hard time with this. I have a Dell PE1800 with a dead LSI card. The LSI had a Raid5 container (3 Maxtors) attached. Dell is shipping me a new one out but I need to be deliberate because I cannot loose the data on the RAID5. Do you know any way I can replace the LSI card and...

Hey there. This is a total newb question but I have a 2801 that is running with a 2mft card in it and I wanted to take a WIC from an older 3600 and put it in. I installed the hardware but upon reload I still dont see the interface and there are probably some config steps I need to go through...

I was wondering if anyone new a source that could help size / compare routers. I am looking at replacing my aging 3600 point to point routers but selecting a new router since they have been phased out comes with questions. I dont need to bundlle all these services into a router. Im looking for...

We have two subnets on our LAN to segment traffic and we are using a windows box as the LAN subnet router. I would like to offload the routing to a Cisco 3640 that is our WAN router with two Ethernet ports. I’m only using one Ethernet port at this time with an ip address on subnet A , Can I...

I am using static routes to manage my WAN right now but I would like to implement RIPv2 . I have used the Router Rip command on each router and entered the IP address of each router for the RIP neighbors but I have no idea how to check to ensure RIP is running properly since my static routes are...

I have a newbie question for you . I have a point to point T-1 down and the CO is telling me its trouble at my A location. I have a LIne Protocol down message and I thought I need to check the clock source on my interface. For the freaking life of me I cannot figure out the command. Clock...

I have a 3600 with DUAL WICS to handle my routing via point to point T-1's to my remote offices. At the hub where the 3600 resides I have two LAN subnets which are routed via a Windows 2003 Server box. I would like to move the routing to the 3600 if it makes sense. I would like to eliminate the...

Is there a way to use ASR without a floppy drive? A flash drive maybe? thanks

Does BCM 3.6 support caller ID over CAS trunks? thanks so much.

We have a BCM 400 3.7 with a Digital Card Module for a t-1 and I have an issue that I have posted previously that I still fight with. 80% of the time everything works perfectly well but then I will get a call from a cell phone from this site saying that there are no lines available. When you...

We have a BCM 400 running 3.6 and I need to make some important changes yet the System configuration tree is not expanding. When I click the expansion icon on Telephony Services the only thing that shows up is the back/restore tool. I restarted the system hoping it would help to no avail. Has...

Hello. I am hoping someone can point me in the right direction. We have a campus LAN with about 200 users housed in 4 campus buildings. Each building is connected via fiber for data and a 50 pair of copper for phone. The LAN has been operational for about 10 years. In the hub wiring closet where...

Hello, need some help finding the right product. I work for a homeless mission in Houston and was recently donated a Cisco 65xx Catalyst with 3 48pt 10/100 modules in it. It works great and I wanted to replace my old daisy chained 10/100 switches in my closet. We have 6 remote buildings linked...

This is a strange issue. We have a BCM 200 with a digital line card installed with 12 lines (the other 12 are for data). Gradually , throughout the day the lines will fill up and we will begin to get "all lines are busy" both on the caller side from outside and the internal callers. When I open...

I have a 3600 that was working fine and it will not load the IOS configuration. When I connect via terminal the System Bootstrap, Version 11.1(20)AA2, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1) Copyright (c) 1999 by cisco Systems, Inc. <---message just scrolls over and over infininetly. I try...

Big problems... We switched over from Analog to Digital trunks so I replaced the analog trunk card with a digital T card. At cut over I had a few problems with the DTI card but eventually I got the lines configured properly and we are all set. However, I am getting complaints that external...

Can you program an ATA device to avoid the prefix dialing. I have an alarm system that needs to dial out and we moved all of our lines to did's .. I have two ata devices but I need to give them direct line access without the prefix thanks . Andrew

Can you program an ATA device to avoid the prefix dialing. I have an alarm system that needs to dial out and we moved all of our lines to did's .. I have two ata devices but I need to give them direct line access without the prefix thanks . Andrew

We just switched from POTS lines to a T1. All of our analog numbers are now DID numbers. I have to configure three of our 24 lines as DID Target lines to go directly to a port ATA to provide Analog (Fax, Elevator,Fire). Issue. I have each Trunk - DN 61-84 to answer automatically. I defined...

Crazy issue with Target Line programing. Our Carrier is sending us 4 digits with DID numbers. I have 4 digits programmed in the BCM. The problem is whenever I configure a target line and enter in the last 4 digits of a phone number that begins with 9 it will not save it. Giving me an error...