Search results for query: *

Hello Guys , we have a large network of 14 X 8600,s with a large overhead of routes using ospf . Does anyone know of any documents/white papers on route summerization that may help me with this . Thanks in anticipation Mucka

Hi guys I have set up successfully a series of filters on Passport.The problem is trying to let one lan communicate with another ie: desination of 10.10.14.0/24 to source of 10.10.28.0/24 forward, to enable pc,s on one side (28) to print to a printer on 10.10.14.0 network.Very simple and...

Hello guys , we are running the above switch manager ver3.0.0.0 when upgrading firmware to our BPS,s we put in our bossXXXX.img and works a treat ,BUT how do we upgrade the diag file ie: boss3005_diag.bin. ?? We tried it in the image field but doesnt work and tried it in the "450/mix stack"...

Hello all , has anyone seen this fault ,very infrequently we have a loss of "Trusted Ports " after a power outage ,resulting in bad voice quality . We do not have a config loss , just Qos advanced ->interface conf->Trusted ports loss. The vlans & ip etc are all ok . Has anyone else seen this .We...

Hello all , we have a default route on our main passport to our internet connection. it is obviously "destination 0.0.0.0" "next hop X.X.X.X" we would like to be able to set another static route BUT on source address instead of destination. I have heard other vendors can do this but I am not...

Hello Al , any help please we recently had a problem were our main 8600 froze .It is a fully polulated box with many stacks/servers/main frames , and other 8600,s hanging off it.We couldnt telnet or device manage it although we coud ping it , unfortunately my collegue didnt have a console cable...

Hello all , we have 2 passports with IST but instead of having SMLT to 5510 stacks ,our customers want 2 seperate 5510,s one from each passport.This is because of the 6 MLT limit per switch. I have done this with the same vlan on each 5510 and the same gateway HOWEVER it reports a ip conflict on...

Hi guys any help please , on a given lan some citrix clients can pick up dhcp others cannot.Same build on all citrix wyse v90 winterm.If we give a static all is ok.Auto is also not an issue we have forced speed and duplex all combinations. Thanks in anticipation Mucka

Hello all , hope you had a good christmas ! bit of advice please , we have two passports connected thro IST on seperate vlan & no OSPF . Would I be correct in having their respective default V1 addresses on the same subnet ? ie: 10.254.254.2 passport A and 10.254.254.3 pasport B./24 mask. This...

hello guys , I wrongly created a role & device association within device setup within policy services ,how can I now delete it ,it doesnt seem to give me the option ,delete is greyed out & a right click only allows a refresh. Any help much appreciated . Thanks Mucka

Hi guys , with 2 8600,s I am trying to implement a single SMLT to a 470 . The IST is configured between passports and when I introduce just one leg of SMLT I get " Funnies " on some of my stacks that connect to one of the two passorts & need a reboot to the stack, as a result of pc,s dropping...

good morning all ,help please ,when we do a save conf ,or implement any config changes our busy 8600 (8690,s with 64 meg),it grinds to a halt and doesnt come back for 20 mins ! We are upgrading to 8692,s shortley with 256 meg. Thanks in anticipation. Mucka

Hi Guys , just installing a new 8600 with 4.0.2.6 ver all works ok but at boot up gives the error SNMP-v3 UMS config error ,using default parameters you would be advised to update. Any help much appreciated Thanks Mucka

Hi guys , took delivery of new 8600 & 2 8692 SF and 48 copper gig blade 8648GTR ,It comes with the ver 4.0.0.0 The passport will not boot the 8648 it tries then gives a handshaking error . I have upgraded the boot monitor and image files but I do not know how to run the gig blade ver...

Hello all, we are having a strange fault with the above message on "i2004" ip phones.Although it thinks there is a conflict ,when we disconnect the phone and ping the address the pings stop ,so there is not really a conflict.It quotes a mac address of 00-0a-e4-70-3f-81 mapped to ip...

Any help guys ? we have many BPS,460,470,s running data & ip phones .somebody told me we could implement both pc & ip phone down the same cat 5 cable hence halving our port consumption,and using vlan tagging and seperate pvid for voice. Any advice on how this works ?? Thanks in advance Mucka

Guys , what is the best way to set passwords for device manager 8600 & BPS/baystack switches ,also telnet & web browse for all the above. Thanks in anticipation Mucka

Question for johnjohn (or anyone)on a previous thread. JohnJohn , you say BPS stacked with 450 will give you QOS on the 450 , how does this work ? & which firmware versions needed for it . Thanks in anticipation Mucka

Question for johnjohn on a previous thread. JohnJohn , you say BPS stacked with 450 will give you QOS on the 450 , how does this work ? & which firmware versions needed for it . Thanks in anticipation Mucka

Hi guys , anyone heard of this one? Stack of two 470,s , one gig module in each & MLT back to 8600. Loss of pings between servers on the same subnet in this stack. Drop one leg of dual nics in server & pings pickup. MLT is tagged . If drop MLT ,problem seems to disapear. Using BOSS3038.img &...