Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations Chriss Miller on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  1. WhiteGooner

    Panasonic NS700 MRG

    Hi guys, I have a strange issue where I have a phone connected via MRG to the main site where the NS700 is installed. There is a SOnicwall at the remote site. When make call there is 1 way speech If I take the Sonicwall out and put a Draytek in, it all works fine. So the Soincwall is...
  2. WhiteGooner

    Pansonic TGP600 using MRG on NS1000

    Hi Guys, Has anyone had any issue trying to get the TGP600 to work via MRG. Registered them on LAN, all good. MRG knows its WAN Getting no registeration attempts. Panasonic have looked at config on both TGP and NS1000 and they say its set up correctly. I'm thinking its the Firewall but...
  3. WhiteGooner

    Panasonic NCP1000 - How do you set MNT port to 'mirror mode'

    Hi, I am having some issues with a delay to connect over a VPN (NCP - NS) (IPGW). When calling from NS, works as expected. When calling from NCP, there is a delay of between 8-10 seconds before you hear ringing. I have had Panasonic Japan look at both configs and the response was that it all...
  4. WhiteGooner

    Calls made via H323 can't press options on AA

    I have a Panasonic NCP500 connected via H323 via a vpn, to a NS700. I have 2 problems: When call is initiated by the NCP it takes around 10 seconds to start ringing the NS. If you call from the NS to the NCP it rings instantly. The other issue is: When making a call from the NCP via the NS...
  5. WhiteGooner

    Office 365 on Panasonic ns700 (Unified Messaging)

    Hi, I am trying to set up a vmail to email notification on a Panasonic NS700. No problems normally, but this is a Office 365 environment. Has anyone worked out a work round to get this to work? Thanks in advance
  6. WhiteGooner

    Panasonic TVP100

    I have a Panasonic TVP 100, the hard drive has failed. I have cloned a hard drive from another TVP, put the hard drive into the faulty unit. It boot's up and goes through the standard wizard. After a short time an error message pop's up stating the hard drive is full! I know it's not as it's...
  7. WhiteGooner

    Ipecs locks up

    Hi Guys, I am predominantly a Panasonic engineer. I have dabbled a bit with Ipecs system as we have a couple customers with this system. The problem I'm having is, a customer has a 30 minute voicemail message, which they want to forward to another user. The original mailbox can play message...
  8. WhiteGooner

    NCP SIP extn card

    Hi, Has anyone ever had this problem: NCP1000 - version 8 Install V-SIPext32 ous try and bring INS Error message: E033102 Card Obstacle Weird thing is this used to work but all of a sudden stopped.
  9. WhiteGooner

    NS700 Unified messaging wrong greeting

    Bit of a strange one. Set up holiday table. System has gone into 'night mode', as its hitting the correct mailbox for night routing, but it plays the no answer greeting in the mailbox rather than the out of hours greeting. Greeting is definatley there as I've checked, it all points to the UM not...
  10. WhiteGooner

    Cant connect to Mitel 3300

    HI, Just received an cxi 3300(2nd hand), i'm trying to connect but when i type in the ip address (found through wire shark), it just times out. I havent connected to one of these for a few years so i might be missing something obvious? Also connected to the rs232 port, im getting information...
  11. WhiteGooner

    Mitel Release 9

    Hi, I wonder if anyone can help, I am certified on Mitel 3300 rel 9.0. I am wanting to get up to speed on the 3300 (MiVoice Buisness) and was wondering whether anyone knows what route I need to take. I am registered with Mitel online but for some reason I cant enroll on the MCD 4.0 update...
  12. WhiteGooner

    NEC XN120 - program headset on a IP2AT-12TXD

    Hi, I'm trying to connect a wired headset to the above handset but cant find a port on the handset, is there a upgrade board for the actual handset to provide a port?, but have found that you can program a headset key on the feature keys, can someone help as it doesnt make sense surely if there...
  13. WhiteGooner

    Message waiting notification on 3rd party

    Hi this is my first post! I was wondering whether any one had installed a 3rd party sip extension, and managed to configure message waiting via a TVM50. I presume it must be a setting on the TVM as the 3rd party app has no settings to configure. Any suggestions would be greatly appreciated.

Part and Inventory Search

Back
Top