Tek-Tips is the largest IT community on the Internet today!

Members share and learn making Tek-Tips Forums the best source of peer-reviewed technical information on the Internet!

Register Log in
  • Congratulations derfloh on being selected by the Tek-Tips community for having the most helpful posts in the forums last week. Way to Go!

Search results for query: *

  • Users: kondalisa
  • Content: Threads
  • Order by date
  1. kondalisa

    CP 600r rlease 5, RJ45 adapter

    Hi,Hi it is CS1000M/81 rls 5.5. I got a new 600r rls 5 server hardware, it has RJ45 connector DS30 on it, i How can i connect server with MGATE card?? in previous hardware there was a 25 pinn D type connector through we connect to MGATE card. I was reading a bulletin regarding CallPilot MPB96...
  2. kondalisa

    Need Advice-CS1000E, Rls 5.5

    Hi, We are going to install 02 CS1000E Rls 5.5 PBX with 100 IP ext in both PBX with SIP connectivity of both PBX and a callpilot 600r at both site.. I was reading NTP`s of planning and engineering about LAN/SIP tips and it has a lot and i cant summarize especially about LAN requirements/Tips. I...
  3. kondalisa

    BCM200-Lost user ID

    Hi, I bought a used BCM200 from a site, but i dont know its user and password as BCM default user and password not working. How can i reset user/password to default value?? or can i recover it by reinstalling software? I would appreciate if somebody help.
  4. kondalisa

    MSDL 0304 Error

    Hi, it is CS1000M/81c rls 5.5. I am so oftenly get following MSDL error and PRI gets disabled and after few minutes enabling/disbaling it gets OK MSDL0304 GROUP 0 MSDL 13 (2) 1911 MSDL0304 GROUP 0 MSDL 13 (2) 1926 ERR9032 3 28 14:55:09 6/05/2009 MSDL0304 GROUP 0 MSDL 13 (2) 1932 MSDL0304...
  5. kondalisa

    COS key

    Hi, it is cs1000 rls 4.5. I have a COS key on attendant console through which we changes COS of different extension on daily basis. How could i avoid attendant to change COS of some executive extensions??? I mean i dont wants attendant to change restriction of some 3 or 4 executive extensions...
  6. kondalisa

    Err5142, No route 14 exist

    Hi, It is CS1000/81c, CPPIV, Release 5.5. I am getting the following error after every 4 or 5 minutes ERR5142 00000000 00000014 >err err5142 > ERR5142 x y Required Configurations for TRO-CM to work is missing. Check TRO( Overlay 16) and/or VTRO ( overlay 17) prompts. Where: X is the...
  7. kondalisa

    MICB Time probelm

    Hi it is CS1000M,MG release 5.5 and ICB rls 4. PBX patches are updated. Problem is that MICB is not synchronizing it times with PABX, it always gets 20 or 30 minutes ahead after every week. I resetted last week MICB due to time problem which was 28 minutes ahead from PBX and after reset it gots...
  8. kondalisa

    Adding keycodes

    Hi I am adding new keycodes to increase 250 extensions in my existing 11c rls 4 pbx. I got two cabinets and cards from Nortel. Need yours advice how to go with this? i mean can i plugged fiber cable with new 02 cabinets while power is ON? and then insert keycode?? Just need your advice how to...
  9. kondalisa

    CODEC question

    Hi, i need some clarification in Codec use, In my element manager Node setup all CODEC options are checked so which CODEC actually will be use for SIP trunks in My NRS? i mean where do we setup which CODEC will be use? and why all CODEC are checked in CODEC option under Node config. It is a...
  10. kondalisa

    IVR-SIP Connectivity

    Hi, I have a CS1000M rls,MG 5.5 working having SIP license also. I also setup NRS between 2 sites i mean this CS1000M,MG and another site having CS1000M rls 5. Now i need to connect it with a 3rd party IVR using SIP, IVR supporst SIP and presently it is connected with another SIP server. I...
  11. kondalisa

    SSH IP phone

    I was reading a thread regarding Nortel IP phone config. settings using SSH. What is SSH and how can i SSH IP phone?? i mean the way or procedure. Thanks in advance.
  12. kondalisa

    Name display problem-NRS

    Hi, i have setup NRS and a CS1k rls 5 system is tied with BCM400 rls 4 using SIP. The problem is that the name display of extension is not displaying on both system extension when they dial each other only Hxxx where xxx is extension number, DChannel is set with IFC=SL1/RCAP=ND3 with no rls ID...
  13. kondalisa

    CFW then operator

    Hi I have a ext=223 which is forward to 255, when an outside calls hits 223 it goes to 255 but when 255 is busy call goes to operator, ext 255 has hunt set to voice mail but call rather go to operator, i just need to drop that call or should go to operator. Further if any extension dont have...
  14. kondalisa

    BCM400 and CS1K NRS

    Hi all. it is BCM 400 and CS1k Release 5. I have setup NRS using SIP between these two. CS1K has assigned a Dynamic IP and it automatically shows IP in Gateway end point. BCM400 wont shows its IP in Gateway endpoints when i assigned it dynamic IP in Gateway endpoints settings so i assigned it a...
  15. kondalisa

    Nortel and Ericsson MD110 QSIG connectivity

    I have connected a Ericcson PBX with Nortel 11c rls 4.5 using E1 connectivity(qsig). It is working Ok accept i dont get name or number when a erricson extension calls nortel pbx extension. i get only the route and member number. I tried different RCAP entries AT nortel pbx but no success. The...
  16. kondalisa

    QSIG connection- Erricson PBX with Nortel PBX rls 4.5

    I i have connected a Ericcson PBX with Nortel 11c rls 4.5 using E1 connectivity. It is working Ok accept i dont get name or number when a erricson extension calls nortel pbx extension. i get only the route and member number. I tried different RCAP entries but no success. The Nortel extension...
  17. kondalisa

    CP 201i, 1.07 with CS1000M rls 5.5

    HI, cana callpilot 201i version 1.07 work with CS1000M,MG release 5.5??
  18. kondalisa

    Huawei switch interoperatibility with CS1K using SIP

    We are integrating a Huawei switch with CS1000E rls 5.5 using SIP/NRS. I managed to call Huwaei extension but when huawei extension call it wont get success i mean call not hitting extension and fast busy on huawei extension, Call from huawei hitting NRS but not routed to CS1K and i think it is...
  19. kondalisa

    PPM setup

    Hi I have a CS1000E rls 5.5. with 02 ISDN PRI. I am trying to setup PPM data so that i can check Pulse metering/Unit charges on my set display. Does somebody ever set that which shows calls unit on set display??? I was trying to configure that but it always stuck on zero wont increment on...
  20. kondalisa

    BC400-CLID dsiplay after call pickup

    Hi I have a BCM 400 rls 4 installed with COMBO 8x32 , 01 GATM8 port card and a PRI card. The PRI card is used for E1 connectivity with CS1K, I am in APAC. I have used CALA profile to installed that BCM. The problem is that i get th CLID on extensions after picking up call, i dont get CLID...

Part and Inventory Search

Back
Top