Search results for query: *

Can I be directed to where the info is relating to the End of Life for Meridian Mail. I have trawled through the Nortel E O L web site and found nothing..... thanks in advance

I am trying to connect US Robotics 56k Faxmodem to Opt 11. This modem does not have any dip switches and I am using Hyperterminal to connect. Trying to use the AT commands one at a time, this is what I get on my PC. Please note that I am in the UK, so it may be that the at&b1 command is not...

Opt 61 rls 25.15 software. I have been asked to provide Auto attendant & ACD queuing for 2 extns. The Auto Attendant is to give callers message that they ar through to dept and in a queue and the ACD to then present calls as the exns become free. It must be very simple and without need to login...

I am short of Digital Extns and have 4 2250's, can I use the PWR tn ports ?

On OPT 61, I need to add 2 Digital Line cards and there are 2 open '0' slots on various shelves, these appear to wired back to main distribution frame. Can they be used and I just ENL card ? and build 1st extn to check it works ?

On Opt 61 using software 25.15 can it provide extn level billing information for network provider. They need to see 1840. DN. number dialled. Have got 1840 workin to select specific route but & LID 1. What else do I need to do ?

I need to change CLS setting from CDMD to CDMA on each extn on OPT61(1200 users) to enable extn level billing (according to Network Provider). Do I have to change each extn individually or is there a way to do it once for all ? thanks

On Opt 61, one of the 2250 Ops consoles is stuck on BUSY. Suggestions on how to release would be appreciated.

Opt 61 getting daily minor alarms - code is NPR 0504 and this relates to incorrect use of Conf should use Ld 34 or Ld 46. Conf Loops seem ok, but any advice would be useful

On Opt 61, a new network provider has been fitted and to ensure that extn level billing is provided, a route code 1840 needs to be 'enabled' so that the provider gets all the info. Can you please advise how is this configured ?

As Meridian Mail is now no longer a 'supported product' will the present software support Call Pilot ? or must I go for system upgrade ?

I need to access Opt 11 remotely and the only way is via modem. What suggestions for best modem to use - based in UK, also any scripts etc to ensure auto answer.

I am trying to set up USR 56k Faxmodem which has no dip switches on Opt 11 and when using some of the commands previously listed for 56k modem, I get error or NO CARRIER. Any ideas ? or should I go for another type of modem, which is a waste as this was found on site.

Getting TIM001 OPRDATA on OPT61, not too sure what to do with it ?

I am getting Minor Alarms and ERR 080 have checked the config of this port and cannot see anything that would cause this problem, any suggestions ??

On the main 2250 Ops console which is manned 24/7, it sometimes goes into Night Service, any suggestions as to what to check to try and stop the problem ?

Currently I am getting OPRDATA 8 1 15 6, any suggestions as to what it is and how to clear it ?

I have an OPT 11 with 2 cabs, 2nd cab has call pilot which is working, but 3 falc cards are dead. One card was changed, with no effect but the problem remains any suggestions ?

Is there a quick method of check the system if you have an alarm. Using LD 32 STAT shows condition of each channel, is there a faster way ?

I have just checked my Call Pilot and there is a message on screen 'Runtime Error - This application has requested the Runtime to terminate it in an unusual way. However I cannot clear this error from the screen'. Any suggestions ?