Search results for query: *

HI Guys, I have been asked to look into enabling quality of service onto the Cisco 887 routers at our remote offices. The routers are running c880data-universalk9-mz.150-1.M3 Our critical applications use telnet and ssh then need to be ordered as access to 10.0.80.80 <plus others in the...

Hi guy's I'm looking into applying Broadcast storm control on the Cisco switches within our network. the commands I'm thinking of applying are: errdisable recovery cause storm-control errdisable recovery interval 180 interface xx/xx storm-control broadcast level 20.00 storm-control action...

Hi Guys, Not sure if this is posted in the right place. Does anyone know if there is a network mapping tools/software out there to map just the Cisco switches and routers on an enterprise network. I've look at Solarwinds LANsurveyor, but this shows all vlans too and the map is just too messy...

Hi Guys, I'm looking into an intermittant dsl connectivity issue at a remote site. The site router is a Cisco 837 f/w version c837-k9o3y6-mz.122-8.YN When i issue the command show dsl interface atm 0 What noise margin levels are acceptable for a stable connection Thanks in advance...

I am getting confused with supernetting. Can someone please help. If I need to further subnet off a class c subnet such that Subnet 1 to have 100 hosts Subnet 2 to have 50 hosts Subnet 3 to have 20 hosts Subnet 4 to have 10 hosts subnet 5 to have 10 hosts These fit nicely into the range using...

I have setup syslog on a HP Procurve 2510-24 Switch (J9019b firmware Q11.11) I am not interested in receiving debug or info messages Is there a command on the switch that will enable logging of events at different levels ie Warnings, Critical etc. many thanks

I get the following message when attempting to add a vlan to a Cisco 3560 switch "2836: .gmt/bst: Platform limit of 128 STP instances exceeded. No instance created for VLAN213 (port Po1). " Then in the running config the following is added: no spanning-tree vlan 213 Do you get an STP instance...

Hi, We use the "banner motd" to display an "Authorised users only" banner when logging onto our Cisco switches and routers. When I use telnet to access the routers this banner is shown before the username/password prompt. When logging on using ssh the banner is displayed after entering the...

Can someone please tell me how to change the admin password on the HP LaserJet P3005 Printer via telnet cli HP JetDirect : J7979E Firmware Version : V.33.57 Many thanks

hi there, Can someone please help. We have recently aquired another business that uses the same private IP address range we use. I have been asked to arrange access to thier hosts from our network. I have read this can be achieved using static NAT statements. I have had a WAN link installed...

Hi guys, can you please help...... I have an inside network of 172.16.1.0 Connected to an outside network of 192.168.1.0 Off of the 192.168.1.0 outside network there is another network of 10.0.0.0 I need all/some of my inside hosts to be able to connect to a single outside host of 10.0.0.1...

We had a power failure that affected our Catalyst 6000's. Following a reboot of the switch, module 16 is no longer available. Module 16 is a multilayer switch featue WS-F6K-MSFC2 and is part of module 2 the supervisor card. The switch has two supervisor cards installed (modules 1 & 2) and the...

I have a Cisco Catalyst 6000 with 2 supervisor cards. One of the supervisor cards recently went faulty and was replaced, but in the mean time additional static route entries were made on the router of the other supervisor card. Is there an easy way of duplicating static route entries from one...

Are there any limits regarding the power output from wireless AP's. I heard somewhere that in the US they can set their AP's to 100mW but in the UK we can only set them for 50mW. Could someone please clarify this.

I have been given some Cisco Aironet 1200 series access points to install in our office. Does anyone know of an idiots step-by-step guide to configuring these. What I really want to do is set up MAC address filtering so that only those MAC addresses in a local table can access my LAN Under the...

Please help I need to set up a LAN-to-Lan connection between two offices. The main office has a Cisco 3000 VPN concentrator The remote office has a Cisco PIX 501 (172.16.54.0 255.255.255.0) The VPN tunnel light stays on but I have no connection to my servers in the main office. I managed to...

Hi Guys, Hopefully this is an easy one for you. I have a Cisco Aironet 340 Access Point (version 11.10T), and I want prevent unathorised access onto my network. I have added the mac address of my wireless adaptor onto the Cisco Aironet and it is there on the existing MAC address filters list...

I am looking into some network traffic monitoring packages for our remote offices. I need to enable netflow on my cisco routers for several packages to work. As I am only looking into this I do not want to make any changes to the network. The IOS I have does not support netflow so I need to add...

I have a server on a remote site that I need to relocate to my main site. So that I do not have to visit each workstation in turn to change the target IP address of the server I intend to use NAT on the remote sites Cisco2651 router. I have added the following into the remote site router...

I am having problems connecting to my citrix ica servers from remote offices. Telnet and ping to the servers is OK. To complicate matters further I use NAT to mask my server address from the users in the remote offices. Is there anyway I can see if UDP packets are being blocked or is there...