Search results for query: *

Hello All Thanks in advance I have an NS700 with version 9 on it All calls are answered by CS1 Option 2 goes to ICD 602 if not answered goes to ICD 601 Option 3 goes to ICD 603 if not answered goes to ICD 601 Option 4 goes to ICD 604 if not answered goes to ICD 601 ICD 601 is fna to 500 If...

Could someone please clarify something for me I am trying to set up a sip trunk on NS700 From reading the posts on here I am wondering should I have 2 IP addresses. I believe my trunk is sip peer trunk Details I was given have 1 IP address for sip server ,no authentation .permit is the static...

Hi Is there any way to see the slot and port that an extension is connected to using PT programming on a TDA 200 Any info on how to assign an extension to a slot/port using PT programming I have gone through all the programming numbers and can't see what I need Thanks in advance

Hello I have a cordless phone as an extension (slt)of a TDA 30 This phone will show caller id if used directly across the pstn Will an ext-cid card allow caller id through to the cordless phone when it is an extension? Thanks in advance

Hello All Just a quick question If you initialise an NS700 with licence key info on it will that licence key be lost Thanks in advance

Hello all I have a tda 30 that loses the customer data after a power down Is the data held on the SD card or on the main board I presume it is on the main board and the battery is dead If so can the battery be replaced ? Thanks In Advance

Hello all Any thoughts about the NS700 and using mobile phones as extensions Do mobile work well as extensions? Will the mobile wake up when a call is incoming I have tried mobiles on a 3cx platform and the push notification does not work reliably. If the mobile phone is asleep the caller gets...

Hi All Hope someone can point me in the right direction Situation is this M2250 is faulty System is in night Set up new extension and pointed NIT1 in to this new extension There are 3 POTS trunks on the system terminated on XFCOT card All 3 three trunks will call in on the new extension ACOD is...

Hello all Can anyone recommend a professional recording service in Ireland to record custom menus for a TVM 50 in the correct format Thanks in Advance

Hello All Your advice requested with the following please Incoming calls answered by custom menu inviting callers to dial 2 for 202,3 for 203 and 4 for 204 If any of the above extensions are busy or no answer the call goes to 201. If 201 is busy or no answer the call goes to the general delivery...

Hello All I have a problem I wonder if you can help I need to use DXDP on a tda 30 , On the slave phone T7633 the display comes up ,I can ring out to another extension from it and I can ring in to the slave.The master phone is a T7633 as well However I have no dial tone on the handset or using...

Hi All Having difficulty connecting to a TES 824 ROM ver Y911AG070731 BX using usb and Ver 3 of console Error Message is "Cannot connect with the PBX of this firmware version or Model Type (01213507H)" Any help greatly appreciated Thanks in advance

Hi All Does the BRA ISDN have to be set at P-P or is it just required that the TDA matches the setting of the ISDN line I have no dial tone for short periods on the 3 basic rates I see a post from OBT with the settings as Permanent Permanent P-P and Fix 0 If the isdn circuits are P-MP must they...

Hello All I have an issue with a KX TA 624 with 2 lines and 8 extensions Both lines are programmed to call on extension 201 under 414 DIL Jack 01 Extension 201 has FWD B/NA active to extension 206 Occasionally other extensions in the premises ring on incoming calls which the customer does'nt...

Hi All Quick question Is caller id built in on the TES824 for the first co 3 lines? I see there is a caller id card 82493,is this for the extra co lines ? Thanks in Advance

Hello All Can anyone tell me if the KX TA 308 is expandable. There is a card KX TA 30874 which looks as if it would provide 8 analogue extensions but I read on some site that the KX TA was not expandable but the only manual I can find seems to refer to an American Version.I am in Ireland...

Hello All KX-TD816 with TVP 50 Been reading posts on systems being hacked to fraudulently make calls By default transfer to outside party is disabled and call forward to outside party is disabled Is this enough ? Should I change the cos of the VM ports to cos 8 Thanks in advance

Hi All I have an 816 (software P411K00306H) with a TVP 50 I have custom menus set up on the TVP and calls are transfered from the VPS to single extensions and to groups with 2 or more extensions. If a call from the VPS goes to a single ext say 205 and is not answered the VPS takes the call back...

Hi All Second problem I have relates to message waiting lamp for GDM system is TD 816 ver 5 with TVP50 VPS Extn 215 is the operator 1 In the VPS programming under operator parameters operators extension is shown as 0 wont let me enter 215 Operator mailbox is 998 Its possible to leave messages...

Hi Can anyone help with this Very frequently I cant get dial tone on these isdn lines ,They are CO 1,2,3,4 and when u press the line keys in turn dial tone will be on the line ., can do this 3/4 time in a row and everything works fine. the next time u try to sieze a line by pressing any of the...