Search results for query: *

I have a hotel with a Hospitality G3r - the PMS link is down. The existing data module is a 7400B. I've ordered a 7400A Data Module and I'm thinking I should order a TN577 as well. 2 questions: will the 7400A work with a G3r PMS link? Also, when the TN577 is replaced, is there any programming...

I have a customer with an Audix LX R1 and it fails backups. The media is SONY CD-RW CRX230E, not a DVD. I need the comcode/part number for the CD/RW drive. Thanks!

Just looking for a simple answer - I hope - customer has Avaya 3720 DECT phones and they need to replace some batteries. Will the phone lose programming? Avaya's doc tells how to replace it and doesn't have a warning about losing settings.

I have a request from a customer on changing the EC500 destination remotely. The instructions look difficult for a non-technical user. Dial telecommuting number Enter SAFE code Enter your extension Enter your station security code Enter your cell number, etc. He's wondering if it could be...

I have a customer who uses 9620 phones - he has one user who makes many outgoing calls a day. He's asking if there is a way to export the call logs from this one phone to a file - obviously he doesn't want to go to the expense of a full-blown CDR install. I don't have a 9620 to play with - mine...

I have a refurb Intuity Audix which was just installed as a replacement - the old one was working but wouldn't back up. Tech onsite did a backup ok and then I tried to do it remotely just for kicks but backup wouldn't start. Error msg was 'A backup cannot be run while another backup is running'...

Customer has a user who does a lot of Message Manager faxing, or did until her laptop was upgraded to Windows 7. Now it doesn't work. Error message says "instfax.bat file can't be found." Anyone have experience with this combination? Thanks.

I have a customer with an S8700 who uses a Verify button to test trunks. It will give dial tone if the trunk is idle and if the trunk is active it gives a warning tone and barges in on the call. Works great on CO trunks but waves him off on ISDN-PRI trunks. Facility Access Code doesn't work on...

I need to remove an IP station and put it back using the duplicate command. Will this work as it does for DCP stations or are there more steps? What info should be saved? This CM is in another state. The station is a 9611. Thanks!

Hi guys. I have a G3r release 011 with ASA access over a network connection. There are 3 others off-site in different states who access this switch and only one of them is having a problem. This guy was able to get in last week with the same settings he has now. The G3 is set to interchange...

I am trying to replace an existing PRI T1 from AT&T with a CBeyond PRI working thru a Cisco router/ IAD. At one point we had the sig. grp. in-serv and the B channels inserv-idle but could not make outgoing calls. The existing ckt. is set for b8zs, esf, conn. network, isdn-pri signaling...

I have an 8300 r15 with 9640's that are going into mute on their own. Random stations- no particular pattern. Anyone seen this one??

I have a MerMsg with selector codes which work correctly on most calls. Occasionally a caller will punch a code and hear ringing- the called party answers and the caller hears the ringing stop but both ends get dead air. We tested on-site and sometimes made 50 calls or more w/o a failure. Tried...

I need to replace a 100R/U with a 100DCD board in a Magix. Is this a plug-in replacement or do I need to remove and replace the programming on this slot? The board is PRI, in the last slot in the switch. After a board renumber, will programming need to be restored or just power off/on? I can't...

When adding an operator to a Magix R4, does the opr. have to be on a certain port- like 01 or 05 on Legend- or can it be any port? 1st carrier only? This system has 1 024 TDL card in slot 1 and 1 412 TDL which is in the 2nd carrier, slot 6. Thanks!

I'm trying to set up remote programming to a an ACS R6 but can't get past retrieving translations. I have a US Robotics Sportster standard modem which works for Definity dialup. Is there a cheat sheet to explain the setup?? Thanks, Cwire

When adding a port network to the 8000 series CM's, what are the options for connectivity? Can customer's existing fiber be used or is IP the only method? Customer wants to avoid buying expensive CP's if possible. Thanks!