Search results for query: *

I show that my CDR Primary link is down. The buffer is maxed at 100%. The secondary shows as active. I have tried busying out the CDR link as well as the Data ext. Nothing seems to be working. How can i get this back up?

My network guy wanted me to move some patch cables around for my 8700 to clean up some data switches. One of them was for a Media-Processor. So I moved it to another switch like he asked, but now if I do a "sta media-p all" I see that: Slot Code Mj Mn Wn Pr Cl El Dup St 01A07 TN2302 0 0...

I was just told by my BP that the IP Office 406 will be "manufactured" discontinued in a couple of months. Has anyone else heard about this?

I have an Avaya 8700 and a Call Manager 4.2 connected using H.323 IP Trunks. I can call from the Avaya to the Cisco perfectly. But cannot call to the Avaya from the Cisco at all. Are the only two things needed to be configured in the Cisco Call Manager the Route pattern and the Gateway...

I have a 7941 phone that when you boot either goes to the "upgrading" screen and sits there or sometimes when you boot sits at the main Cisco screen and has what looks like a bullseye painted on it. Any thoughts?

I am setting up a new Codec for some VOIP trunks between sites. I made the changes and hit enter but the CM is telling me that "WARNING: Change may interrupt audio to IP endpoints until they are rebooted" Does this mean only IP endpoints associated with this codec or ALL IP endpoints will be...

Hello all, had a quick question for you. my Networking manager gets nervous when he looks at my stack of 3 G700's and only sees one network cable plugged into the network. Can I plug in the other two G700's into the network as well for some redundancy? If so are they regular patch cords or...

I have a Communication Manager server here on site that runs a remote site in another state. We run a different PBX here( Avaya) but I have purchased two 7941's I would like to get working here for a lab type environment. I don't need any outbound calling trunks added, I just would like to get...

I have a Avaya Definity (R4.0)and Cisco Call Manager in the same Computer room. (Don't ask...LOL) Is there any way i could set up four digit dialing between the two systems? What hardware would I need? My manager is a Cisco nut and wants to start replacing all of our remote locations with...

Real quick question. I have just started here at a new place and found that the PCMCIA cards were never inserted into the 8700's. Can this be done at any time or should I power down the 8700's after hours and then bring them back up? Basically...are the PCMCIA cards hot swappable? Thanks...

I am adding a new G700 at a remote site. I already have 5 G700's with a 8300 there working fine. I have entered all the settings correctly and yet it will still only register to the 8300 and not back at my CLAN card at main office. I have busied out, and reset the CLAN card and the other...

Hello all. I have a problem I hope you can solve to save me some programming. We are switching carriers from AT&T to Global Crossing. I have about 80+ DID's from AT&T where they are sending me 3 digits for my 4 digit ext. So they send me 702...and I route it to 2702. In my trunk group I...

I have a LSP with a 8300 with 5 g700's. Last night the link went down but is back up now. My 8300 and the 2nd g700 are up but the last 3 g700's are not linking up... HELP! Any suggestions?

Is there any way to call a station and immediately have the ext you called go off hook? If any of you are familiar with the Toshiba phone systems you should know what I am talking about. You basically call someone you know is there and it goes speaker phone right away and the person you...

We have an IVR here at my work and I was just curious as to what is the expected % of people getting kicked out due to inputing something wrong? We seem to get about 10%-15% of the people complaining they were kicked out after they "correctly answered the question". I know people cannot...

Last night I moved my 8700's and three cabnites to a new server room. I took pictures and documented everything. Everything is plugged in exactly where it should be. But when I log into CM and do a "List config all" it shows that all my boards are listed as "NO BOARD". Please help!!!

Hello all. We are building a new Data Center in our building. So this weekend I will be moving my entire phone system. (Duel 8700's with 3 cabinets) Anything I should look for or know before I bring them down on Friday? Or when I bring them back up?

I have a weird problem...aren't all problems "weird"? Anyhow... I have had a bunch of reports from users that claim that they are talking on a call for 7-10 min then all of a sudden there is static on the call and they can't hear the customer. After they call them back the customer says they...

I am a Definity guy trying to live in a Partner world...LOL. I have placed some ICM Page buttons on the phones here, but instead of them going immediatly off hook at the called station they would like it to ring first. Any idea how i do that? Thanks.

Is there any kind of silent monitoring on the Partner system?